521910

I-onik WS-102 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
English
Please keep these instructions in a safe place for future reference.
Kit Contents:
1x i.onik
®
Door/Window Sensor
1x Magnetic contact
1x Double-sided adhesive pad
1x Instruction leaet
1. Introduction
The i.onik
®
Door/Window Sensor consists of two parts, a transmitter
and a magnetic contact. Once this sensor is installed, with the trans-
mitter fastened to the frame and the magnet to the door or window,
the sensor will trigger and transmit a message to the i.onik
®
Alarm-
system Smart Panel when the door or window is opened.
2. Location
First determine the location of the Sensor, which should be placed:
• In the most vulnerable rooms or near key entry/exit points.
• Away from extreme temperature sources (radiators, ovens, stoves
etc.) and large metal objects that could interfere with the wireless
performance.
• Away from direct sunlight.
• Indoors only and not behind partitions.
• Where better transmitter/reception performance can be
achieved (if necessary).
3. Installation and Operation
3.1 Powering up the Door/Window Sensor
• Remove the battery cover; insert new
batteries noting the polarity as shown in
Fig. 1 and replace cover. (Requires
2x AAA batteries)
• Low battery indication: If the batteries need
to be replaced, the RED LED on the transmitter
will ash slowly.
3.2. Installing the Door/Window Sensor
• Mount the transmitter on a xed surface such as a door or a window
frame.
• Mount the magnet on a movable surface such as a door or a window.
• Ensure the >/< marks on the sides of the transmitter and magnet
match up as shown in Fig. 2.
• The transmitter and the magnet
must be no more than 5 mm
apart.
3.3. Mounting with the Double-
Sided Adhesive Pad
• Ensure the mounting surface is
clean.
• Peel back one layer of the protective
lm and attach it to the transmitter.
• Peel back the remaining layer of protective lm and press the trans-
mitter rmly in place against the mounting surface until rmly
attached.
• Repeat to attach the magnet.
4. House Security Code Settings
Unless the factory settings of the i.onik
®
Alarmsystem Smart Panel
have been altered, the House Security Code will NOT need to be
changed.
However, if the settings on the Smart Panel have been altered, or
need to be altered to solve the problem of the Smart Panel and sen-
sors activating intermittently (or not working at all) or interference
with other systems, then the House Security Code on all system
modules (sensors and sirens)will also need to be changed.
House Security Code settings can be altered as follows:
• There are 4 jumpers or dip-switches on each device.
• Remove the jumper compartment cover, then pull out or plug the
jumper into the contacts to change the House Security Code.
• If a jumper is plugged it is ON if it is removed it is OFF.
Default code is with all the jumpers plugged.
• To ensure the system works correctly, make sure the jumpers on
the Smart Panel and all other system modules (sensors and sirens)
match exactly.
Jumpers for house security code - Smart Panel
- Each sensor
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
*Jumper:
ON = Plugged,
OFF = Pull Out
Dip-Switches for house security code
- Key Fob Remote
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
5. Zone Code Settings
The sensor is supplied with a pre-assigned Zone setting. The sensor
can be assigned to a different zone as follows:
• Unscrew and remove the jumper compartment cover on the rear of
the sensor.
• In the area marked “Zone Code” there are eight pairs of
metal contacts with a number next to each.
• The number corresponding to the pair of contacts which is plugged
with a jumper is the current zone.
• To re-assign to a different zone simply unplug the jumper from its
current zone and plug it across the contacts corresponding to the
new zone number selected.
Jumpers for zone code Default zone code: Zone 1
6. Maintenance
The product may be cleaned with a soft damp cloth and then wiped
dry. Do not use abrasive, solvent based or aerosol cleaners as this
may damage and/or discolour the product.
Do not allow water to enter or attempt to clean inside the unit.
7. Batteries
Do not allow the batteries to corrode or leak as this may cause per-
manent damage to the product. Take care to insert the batteries with
the correct polarity as shown inside the battery compartments. Do not
mix new and old batteries or different types of batteries. Do not use
rechargeable batteries.
At the end of their useful life the batteries should be disposed of
via a suitable recycling centre. Do not dispose of with your normal
household waste. DO NOT BURN.
8. Alarm System Limitations
Even the most advanced alarm systems cannot guarantee 100 % pro-
tection against burglary or environmental problems. All alarm systems
are subject to possible compromise or
failure-to-warn for a variety of reasons.
Please note that you may encounter problems with your system
if:
• The Smart Panel is not placed within hearing range of persons slee-
ping or remote parts of the premises.
• The sensors are placed behind doors or other obstacles.
• Intruders gain access through unprotected points of entry (where
sensors are not located).
• Intruders have the technical means of bypassing, jamming,
or disconnecting all or part of the system.
• The power to the sensors is inadequate or disconnected.
• The sensors are not located in proper environmental/temperature
conditions i.e. too close to a heat source.
Note:
Inadequate maintenance is the most common cause of alarm
failure; therefore, test your system at least once per week to
be sure the sensors and sirens are working properly.
Although having an alarm system may make you eligible for
reduced insurance premiums, the system is no sub-stitute for
insurance.
Fig. 1
Transmitter
Magnet
Battery Compartment
Cover
2x AAA Batteries
(not incl.)
Fig. 2
Chips and More GmbH
Gewerbestr. 7 | 79112 Freiburg | Germany | www.i-onik.de
Service: + 49 7664 403 69 12
Email: support@i-onik.de
Weitere Informationen und Erklärungen zur Handhabung des Alarmsystems finden Sie unter www.i-onik.de
For more details and questions on how to operate the alarm kits, please go to www.i-onik.de
hometec
hometec
WS-102
Quick Start Guide
Door/Window Sensor
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for I-onik WS-102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of I-onik WS-102 in the language / languages: German as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info