627045
9
Zoom out
Zoom in
Previous page
1/16
Next page
9
ÄNDERUNGEN UND IRRTÜMER VORBEHALTEN ÄNDERUNGEN UND IRRTÜMER VORBEHALTEN
Nr. Beschreibung Art-Nr. Nr. Beschreibung Art-Nr.
54 Konische Befestigungsschraube
von Kopf
129 Stift
55 Klemmbüchse 130 Arm
56 Keil 131 Schaltwelle 500603
57 Schneckenrad Z28 501234 132 Stift von Schalthebel 504323
58 Büchse 133 Schalthebel 500243
59 Zahnradwelle 134 Feder von Schalthebel 501306
60 Zahnrad Z17 510236 135 Kugel von Schalthebel 504348
61 Stange Gehäuse mit Anschlüssen 500037
62 Stütze Klemmungssat Kopf (Nr. 61 bis zum
67+70+72+73)
500593
63 Knopf von Hebel M10 500632 Schaltarmsatz (129 + 130) 501043
64 Stange von Klemmhebel Spindel komplett (40 bis zum 52) 500984
65 Bracket von Hebel Feder und Gehäuse (78+80) 501312
66 Stift Schutzkappe Motor 504124
67 Federring Bohrfutterschutzkappe 500304
68 Unterlegscheibe Spindelantriebwelle (115+124) 500030
69 Gehäuse Hebelsatz von Kopf- und
Tischverstellung (17+18)
500448
70 Klemmbolzen Zubehör 501242
71 Rundkopfschraube Transformator 3x230V ein, 3x400V aus 501260
72 Sechskantmutter Verstellungeinrichtung Tisch 501315
73 Sicherungsmutter Verstellungseinrichtung Kopf 501316
74 Rundkopfschraube Schalter 504402
75 Abdeckung Not-Aus 500704
6. KonstrUKtIon Und nachstellUng
Die Säule ist im Säulenfuß montiert. Klemmhebel 63 (Abb. 5) von der Pinole lockern und Hebel 17 (Abb. 2)
drehen um den Kopf vertikal zu verstellen. Klemmhebel 63 wieder festdrehen wenn der Kopf in der gewünschten
Position gedreht ist. Mutter 73 (Abb. 5) lockern und Mutter 72 drehen zur Nachstellung der Klemmung. Die
Position des Klemmhebels kann auch auf diese Weise nachgestellt werden. Mutter 73 wieder festdrehen.
Das Zahnradgehäuse ist auf dem Spindelkopf montiert und darauf sitzt der Motor. Die Pinole kann vertikal
nachgestellt werden (Pinolenvorschub) durch das Drehen der Vorschubhebel 89 (Abb. 5). Zahnradgehäuse und
Motor entfernen, Ring 41 (Abb. 4) lockern und Mutter 40 drehen um das Spiel des Spindellagers nachzustellen. Im
Herstellerwerk wurde das Spiel bereits nachgestellt. Sie brauchen das Spiel nicht nochmals nachzustellen (dies
soll nur von Fachpersonal gemacht werden).
7. ÜBertragUng
Umdrehungszahl (Abb. 6): Die Bewegung der Ausgangswelle vom Motor (Welle I) wird übertragen auf
Welle II mittels Zahnräder 95/126 (oder 99/100) und weiter mittels Zahnräder 102/123 (oder 108/119) auf
Welle III. Schließlich wird die Bewegung übertragen auf die Spindel durch Führung und Keil. Die Motor
hat 2 Geschwindigkeiten - zusammen mit Schaltung vom Zahnradgetriebe (4 Möglichkeiten) gibt es 8
Umdrehungsgeschwindigkeiten.
Pinolenvorschub: Die Überbringung ist im Spindelgehäuse montiert. Die Pinole ist nach oben und nach unten
zu bewegen durch Betätigen des Vorschubhebels 88 (Abb. 5). Die Bewegung wird übertragen auf die Pinole
mittels eines Zahnrades und der Zahnstange der Pinole.
Kopfverstellung: De Kopf ist drehbar, und nach oben und unten von Hand verstellbar um die Vertikalsäule.
Klemmhebel 63 (Abb. 5) losdrehen, Kurbel 17 (Abb. 2) hierzu drehen. Wenn Hebel 63 wieder festgedreht wird,
kann die Maschine wieder für Arbeiten eingesetzt werden.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 25 T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 25 T in the language / languages: German as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 25 T

Huvema HU 25 T User Manual - English - 16 pages

Huvema HU 25 T User Manual - Dutch - 16 pages

Huvema HU 25 T User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info