627038
7
Zoom out
Zoom in
Previous page
1/16
Next page
7
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
6.1 diepte instellen
De diepte-instelling B bevindt zich bij de zijspindel. Maak de stelbout A los
en ga naar de juiste positie. Maak de stelbout weer vast en laat de spindel
terugkomen (afb. 6).
6.2 snelheid aanpassen
Stekker van de machine uit het stopcontact halen.
De V-snaar beschermkap openmaken en de V-snaar spanhendel terughalen.
Kies de gewenste boorsnelheid en verplaats de V-snaar naar de juiste positie.
Duw de motor naar achteren totdat er een matige spanning op de V-snaar staat. Zet de hendel weer vast.
De juiste snelheid voor een bepaalde afmeting boor is in de tabel af te lezen:
Diameter
van boor
Gietstaal Gereedschapstaal Gietijzer Zacht staal Aluminium /
koper
Snijsnelheid
m/min feet/
min
m/min feet/min m/min feet/
min
m/min feet/
min
m/min feet/
min
12 40 18 60 24 80 30 100 60 200
mm Inch Toerental op basis van boordiameter en snijsnelheid
2 1/16 1910 2445 2865 3665 3820 4890 4775 6110 9550 12225
3 1/8 1275 1220 1910 1835 2545 2445 3185 3055 6365 6110
5 3/16 765 815 1145 1220 1530 1630 1910 2035 3820 4075
6 1/4 610 610 955 915 1275 1220 1590 1530 3180 3055
8 5/16 480 490 715 735 955 980 1195 1220 2390 2445
10 3/8 380 405 570 610 765 815 955 1020 1910 2035
11 7/16 350 350 520 525 700 700 870 870 1740 1745
13 1/2 300 305 440 460 590 610 735 765 1470 1530
16 5/8 240 245 360 365 480 490 600 610 1200 1220
19 3/4 190 205 285 305 380 405 480 510 955 1020
3-2.Operation illustration and procedure:
1. There are three T grooves in the worktable. It is used to fix the work piece.
1-1.There are two T grooves in the base, too. It is convenient for fixing the longer, heavier and larger
working piece.
OPTION
2. The pulley cover is strictly prohibited to open in normal operation condition.
3. Protect safety guard shall be allocated in a proper position in operation. It is controlled by a micro
witch. (For CE)
4. Adjustment of feeding limit
To prevent unwanted penetration to work piece, the feeding limit
shall be set by adjusting the appropriate position of feeding depth
fixing button as long as the distance between the end of tool and
top surface if work piece is measured.
A. Setting of feeding depth
1. Loosen knob A.
2. Turn scaled ring B to desired feeding depth.
3. Lock knob A.
15
Lock
Loose
Afbeelding 6
JTD-19 series
1. Loosen knob B on both sides of headstock.
2. Push handle A forward as arrow sign to get belt tension.
3.Lock knob B firmly to fix belt tension.
When speed change is required. Loosen lead bolt (parts no. 22-S2) on both side of headstock. Pull belt
handle (parts no. 26) to allow belts repositioning and then move belts to correct groove to acquire
desired speed. See following speed chart for reference.
JTD-19series
For proper belt tension, use 10 1bs pressure or hand pressure on the belt as shown as bellow.
Models belt model tables
17
Machine model
Belt specifications
Quantity
JTD-19series
FM-42.5
1
B
A
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 20F SUPER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 20F SUPER in the language / languages: Dutch as an attachment in your email.

The manual is 3,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 20F SUPER

Huvema HU 20F SUPER User Manual - English - 16 pages

Huvema HU 20F SUPER User Manual - German - 16 pages

Huvema HU 20F SUPER User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info