477591
67
Zoom out
Zoom in
Previous page
1/80
Next page
67
6
Austauschen Des Motorantriebsriemens
Parken Sie den Traktor auf einer ebenen Fläche. Legen
Sie die Handbremse ein. Für einen leichteren Service gibt
es unten am linken Fußtritt ein Klebebild mit Anleitung zum
Installieren des Riemens.
ENTFERNEN DES RIEMENS -
1. Entfernen Sie den Mäher (siehe “ENTFERNEN DES
MÄHERS” in diesem Abschnitt des Handbuchs).
ANMERKUNG: Merken Sie sich die Lage des ganzen Mo-
torantriebsriemens und die Position alle Riemenführungen
und Halter.
2. Trennen Sie den Kabelbaum der Kupplung (A).
3. Entfernen Sie die Antirotations-Verbindung (B) an der
rechten Seite des Traktors.
4. Nehmen Sie den Riemen von der feststehenden Freilau-
frolle (C) und von der Kupplungs-Freilaufrolle (D) ab.
5. Entfernen Sie den Riemen von der mittleren Spann-
Freilaufrolle (E)
6. Ziehen Sie den losen Riementeil zum Heck des Traktors.
Nehmen Sie den Riemen nach oben ab vorsichtig von
der Transmissionsscheibe, indem Sie ihn über die Flügel
des Kühlungsventilators (F) hochheben.
7. Nehmen Sie den Riemen nach unten von der Motorscheibe
und rund um die elektrische Kupplung (G) ab.
8. Schieben Sie den Riemen zum Heck des Traktors von
der Steuerungsplatte (H) herunter und entfernen Sie ihn
vom Traktor.
INSTALLIEREN DES RIEMENS
1. Installieren Sie den neuen Riemen vom Heck des Traktors
nach vorne über die Steuerungsplatte (H) und oberhalb
der Welle des Kupplungs-/Bremspedals (J).
2. Ziehen Sie den Riemen zur Kühlerseite des Traktors und
führen Sie ihn rund um die elektrische Kupplung und auf
die Motorscheibe (G).
3. Ziehen Sie den Riemen zum Heck des Traktors. Legen
Sie den Riemen vorsichtig hinunter rund um den Trans-
missions-Kühlungsventilator und auf die Eingangsscheibe
(F). Vergewissern Sie sich, dass der Riemen innerhalb
des Riemenhalters ist.
4. Installieren Sie den Riemen auf der mittleren Spann-
Freilaufrolle (E).
5. Installieren Sie den Riemen auf der feststehenden Freilau-
frolle (C) und auf der Kupplungs-Freilaufrolle (D) ab.
6. Bauen Sie die Antirotations-Verbindung (B) an der rechten
Seite des Traktors wieder ein. Ziehen Sie die Schrauben
fest an.
7. Schließen Sie den Kabelbaum der Kupplung (A) wieder an.
8. Vergewissern Sie sich, dass der Riemen in allen Scheiben-
rinnen und innerhalb aller Riemenführungen und Halter
verläuft.
9. Installieren Sie den Mäher (siehe „EINBAU DES MÄH-
DECKS“ in diesem Abschnitt des Handbuchs).
electric
02953
A
B
C
D
E
F
G
H
J
To Replace Motion Drive Belt
Park the tractor on level surface. Engage parking brake.
For ease of service there is a belt installation guide decal on
bottom of left footrest.
BELT REMOVAL -
1. Remove mower (See “TO RE MOVE MOWER” in this
section of manual).
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
2. Disconnect clutch wire harness (A).
3. Remove anti-rotation link (B) on right side of tractor.
4. Remove belt from stationary idler (C) and clutching idler (D).
5. Remove belt from centerspan idler (E).
6. Pull belt slack toward rear of trac tor. Carefully remove
belt up wards from trans mis sion input pulley and over
cooling fan blades (F).
7. Remove belt downward from engine pulley and around
electric clutch (G).
8. Slide belt toward rear of tractor, off the steering plate (H)
and remove from tractor.
BELT INSTALLATION -
1. Install new belt from tractor rear to front, over the steering
plate (H) and above clutch brake pedal shaft (J).
2. Pull belt toward front of tractor and roll belt around electric
clutch and onto engine pulley (G).
3. Pull belt toward rear of tractor. Carefully work belt down
around transmission cooling fan and onto the input pulley
(F). Be sure belt is inside the belt keeper.
4. Install belt on centerspan idler (E).
5. Install belt through stationary idler (C) and clutch ing idler (D).
6. Reinstall anti-rotation link (B) on right side of tractor.
Tighten securely.
7. Reconnect clutch harness (A).
8. Make sure belt is in all pulley grooves and in side all belt
guides and keep ers.
9. Install mower (See “ASSEMBLY OF THE CUTTING UNIT”
in this sec tion of manual).
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna YTH223T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna YTH223T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info