477575
40
Zoom out
Zoom in
Previous page
1/72
Next page
40
5
IMPORTANT! COLD STARTING FOR HYDRO
COLD STARTING FOR HYDRO (BE LOW 40°F[4°C]) - AF TER
STARTING ENGINE AND BEFORE DRIVING, LET TRANS-
MISSION WARM UP FOR ONE (1) MINUTE BY PLACING
MOTION CONTROL LEVER IN NEU TRAL (N) PO SI TION
AND RELEASING CLUTCH/BRAKE PEDAL.
WICHTIG! KALTSTARTEN FÜR MASCHINEN MIT
HYDROSTATISCHEM GETRIEBE
FÜR TEMPERATUREN UNTERHALB VON 40° (4°C).
NACH DEM ANLASSEN DES MOTORS DAS GETRIEBE
(1) MINUTE LANG AUFWÄRMEN LASSEN, BEVOR LOS-
GEFAHREN WIRD. HIERZU DAS SCHALTGETRIEBE IN.
ATTENTION : DEMARRAGE A FROID D'UNE
TRANS MIS SION HYDROSTATIQUE.
PAR UNE TEMPERATURE INFERIEURE A 4°C : APRES
AVOIR DEMARRE LE MOTEUR ET AVANT DE DEPLAC-
ER LE TRACTEUR, LAISSER LA TRANS MIS SION SE
RECHAUFFER PENDANT UNE MINUTE OU PLUS, EN
PLACANT LA COMMANDE DE VITESSE SUR SA PO SI TION
NEUTRE (POINT MORT) ET EN RELACHANT LA PEDALE
D'EMBRAYAGE/FREIN.
IMORTANTE! Empieso en Frío para hidros-
tático
PARA TEMPERATURA MENOR QUE 40°F (4°C). DESPUÉS
DE HABER EMPESADO EL MOTOR Y ANTÉS DE CON-
DUCIR, DEJE QUE LA TRASMICIÓN SE CALIENTE
DURANTE (1) MINUTO PONIENDO EL DISPOSITIVO DE
CAMBIO A NEUTRO (N) Y SOLTANDO EL PEDAL DEL
EMBRAGUE/FRENO.
ATTENZIONE! AVVIAMENTO A FREDDO PER
TRASMISSION!
PER TEMPERATURE INFERIORI AL 40°F (4°C). DOPP
AVER AVVIATO IL MOTORE, E PRIMA DI METTERLO IN
AVANZAMENTO, LASCIARE RISCALDARE IL GRUPPO
TRASMISSIONE PER UN (1) MINUTO METTENDO IL
CAMBIO IN FOLLE E DISINNESTANDO IL PEDALE DEL
FRENO/FRIZIONE.
BELANGRIJK! LOUD STARTEN VOOR HYDRO
VOOR TEMPERATUREN ONDER 40°F (4°C). NA HET
TARTEN VAN DE MOTOR EN VÓÓR HET RIJDEN DE
TRANSMISSIE (1) MINUUT WARM LATEN LOPEN DOOR
DE VERSNELLINGSHENDEL IN NEUTRAAL TE PLAATSEN
EN HET REM/KOPPELINGSPEDAAL LOS TE LATEN.
PURGE TRANSMISSION
To ensure proper operation and performance, it is rec om -
mend ed that the transmission be purged before op er at ing
tractor for the fi rst time. This pro ce dure will remove any trapped
air inside the trans mis sion which may have de vel oped during
ship ping of your tractor.
IMPORTANT: SHOULD YOUR TRANSMISSION RE QUIRE
REMOVAL FOR SERVICE OR RE PLACE MENT, IT SHOULD
BE PURGED AF TER REIN STALLATION BEFORE OP ER -
AT ING THE TRAC TOR.
Park tractor on level surface so it will not roll in any direc-
tion. Parking brake must be disengaged for the following
procedure.
Disengage transmission by placing freewheel con trol in
free wheel ing position.
Start engine and move throttle control to slow position.
Be sure parking brake is not engaged.
Move motion control lever to full forward position and hold
for fi ve (5) seconds. Move lever to full reverse position
and hold for fi ve (5) seconds. Repeat this pro ce dure
three (3) times.
Move motion control lever to neutral (N) position.
Stop tractor by turning ignition key to "OFF" po si tion.
Engage transmission by placing freewheel control in
driving po si tion.
Start engine and move throttle control to slow position.
Drive tractor forward for approximately fi ve feet then
backwards for fi ve feet. Repeat this driving procedure
three times.
Your tractor is now ready for normal operation.
ENTLÜFTEN DES GETRIEBES
Um vorschriftsmäßigen Betrieb und einwandfreie Leistungs-
fähigkeit des Getriebes zu gewährleisten, sollte dieses vor
der ersten Inbetriebnahme des Traktors entlüftet werden. Auf
diese Weise wird sichergestellt, daß sämtliche Luftblasen,
die sich während des Transports des Traktors im Getriebe
gebildet haben könnten, entfernt werden.
WICHTIG: FALLS DAS GETRIEBE FÜR ETWAIGE WAR-
TUNGSARBEITEN ODER ZUM ERSATZ AUSGEBAUT
WERDEN MUSS, SOLLTE ES NACH DEM WIEDEREINBAU
IM TRAKTOR ENTLÜFTET WERDEN, BEVOR DIESER IN
BETRIEB GENOMMEN WIRD.
Den Traktor auf ebenem Boden abstellen und sicherstel-
len, daß er nicht ins Rollen kommen kann. Für diesen Vor-
gang kann die Feststellbremse nicht eingelegt werden.
Das Getriebe auskuppeln, indem die Freilauf-Schaltung
auf Freilauf geschaltet wird.
Den Motor anlassen und die Gasbedienung auf langsamen
Leerlauf stellen. Sicherstellen, daß die Feststellbremse
nicht eingelegt ist.
Den Gangschalthebel ganz in die Vorwärtsstellung rücken
und fünf (5) Sekunden festhalten. Dann den Hebel ganz
in die Rückwärtsstellung rücken und ebenfalls fünf (5)
Sekunden lang festhalten. Dieses Verfahren dreimal (3)
wiederholen.
Den Gangschalthebel auf die Neutral-Stellung (N)
rücken.
Den Traktor abstellen, indem der Zündschlüssel in die
“AUS” (OFF) Stellung gedreht wird.
Die Freilauf-Schaltung in die Fahrtstellung rücken, um
das Getriebe einzukuppeln.
Den Motor anlassen und die Gasbedienung auf langsa-
men Leerlauf stellen.
Den Traktor etwa 1,50 m (5 ft) weit nach vorne fahren
und dann um etwa 1,50 m (5 ft) zurücksetzen. Dieses
Verfahren dreimal wiederholen.
Der Traktor ist jetzt normal betriebsbereit.
PURGE DE LA TRANSMISSION
Pour assurer un fonctionnement et un rendement corrects,
il est recommandé de purger la transmission avant d'utiliser
le tracteur pour la première fois. Cette opération supprimera
l'air emprisonné à l'intérieur de la trans mis sion pendant le
transport du tracteur.
ATTENTION! SI LA TRANSMISSION A ETE DE POSE
POUR SON ENTRETIEN OU SON REMPLACEMENT,
ELLE DEVRA ETRE PURGEE APRES SON REMONTAGE
ET AVANT REUTILISATION DU TRACTEUR.
Placer le tracteur sur une surface plane afi n qu'il ne
puisse pas rouler dans aucune direction. Le frein de
stationnement doit être desserré pour effectuer les
opérations suivantes.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna YTH151 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna YTH151 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info