477663

Husqvarna TR430 Manual

2
Zoom out
Zoom in
Previous page
1/60
Next page
7
1. Gearcase notch
2. Handle lock
3. Handle (high po si tion)
4. Shift lever
5. Handle (low position)
6. Handle lock lever
2. Assembly 2. Zusammenbau
2. Montage 2. Montaje
2. Montaggio 2. Montering
Install handle
a. Insert one handle lock (with teeth facing outward) in
gearcase notch (fig. 1). Apply grease on smooth side
of handle lock. This will aid in keeping lock in place until
handle is lowered into postion.
b. Grasp handle assembly, ease han dle base into "up" posi-
tion as shown in figure 2. Be sure handle lock remains
in gearcase notch. Be careful not to stretch or kink
cables.
c. Rotate handle assembly down. Insert rear carriage bolt
(fig. 3-inset) first, with head of bolt on L.H. side of tiller.
Insert front pivot bolt. Lower the handle as sem bly. Tighten
bolts so han dle moves with some resistance.
d. Insert second handle lock (with teeth facing inward) in
slot handle base (fig. 3-inset).
e. Place washer on threaded end of handle lock lever.
f. Insert handle lock lever through handle base and gear
case (fig. 3-inset).
g. With handle assembly in lowest position, securely tight en
handle lock lever by rotating clock wise.
1
2
Figure 1
Figure 2
1. Getriebegehäuse-Aussparung
2. Handgriffsperre
3. Handgriff (obere Stellung)
4. Schalthebel
5. Handgriff (untere Stellung)
6. Hangriffsperrenhebel
Montage des Handgriffs
a. Eine Handgriffsperre (mit den Zähnen nach außen) in die
Aussparung des Getriebegenhäuses einpassen (Abb. 1).
Die glatte Seite der Handgriffsperre mit Fett schmieren.
Auf diese Weise wird die Sperre in der Aussparung ge-
halten, bis der Griff angebracht worden ist.
b. Handgriff fassen und die Handgriffplatte gemäß (Abb. 2)
in die obere Stellung bringen. Kontrollieren, ob sich die
Handgriffsperre noch in der Aussparung des Getriebege
häuses befindet. Kabel dürfen nicht gestreckt oder ver-
heddert werden.
c. Den Handgriff nach unten schwenken. Den hinteren Bol-
zen (abb. 3 ausschnitt) mit dem Bolzenkopf auf die linke
Seite der Bodenfräse gerichtet, zuerst anbringen. Den
vorderen Gelenkbolzen einsetzen. Hangriffmontagesatz
senken. Die Bolzen so festziehen, daß die Handgriffe
beim Bewegen etwas Widerstand leisten.
d. Die andere Handgriffsperre (mit den Zähnen nach innen)
in den schiltz der Handgriffplatte einpassen (abb. 3 aus-
schnitt).
e. An dem mit Gewinde versehenen Ende des Handgriffs
perrenhebels eine Unterlegscheibe anbringen.
f. Handgriffsperrenhebel durch die Handgriffplatte und das
Getriebegehäuse stecken (Abb. 3 ausschnitt).
g. Mit dem Handgriff in der untersten stellung, ist der
Handgriffsperrenhebel durch Drehen im Uhrzeigersinn
festzuziehen.
Abb. 1
Abb. 2
3
4
5
6
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna TR430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna TR430 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info