518170

Husqvarna SCANDINAVIA 400 Manual

61
Zoom out
Zoom in
Previous page
1/64
Next page
61
Care of your Scandinavia 400
Incorrect stitch
If the machine does not sew the
stitch indicated by the Infodisplay, it
is possible that the electronics have
been disturbed in some way, perhaps
by a short power cut or electrical
disturbance. Shut off the main switch,
wait a few seconds and try again. If
the fault remains, contact your dealer.
Machine runs sluggishly
Dirt or lint has built up under the
stitch plate. Loosen the plate and
brush clean between the feed teeth and
in the bottom area. See page 59.
Main motor does not work
The electronic overload protector may
have switched off. Shut off the main
switch, wait about a minute. Then turn
the machine back on.
Balance setting for buttonhole
Balance can only be set if a buttonhole
is selected. Press the buttons
until the letters BAL are indicated to
the left on the Infodis play. Instead of
the stitch length indication, a balance
indication is now shown. When you
wish to increase the density of the
right column, press stitch length
button (-). When you wish to decrease
the density, press stitch length button
(+).
The balance can be set between -5
to +5. The balance indication on the
Infodisplay will change in steps with
each touch. When you select an other
stitch, the display goes back to show
the sitch length indication. The
machine always retains the last balance
setting that has been made.
The sewing and embroidery
machine screen does not respond
to touch
The socket on the back of the machine
where the embroidery unit is connected
can be sensitive to static electricity when
the embroidery unit is not connected.
If the sewing machine screen does not
respond to touch, turn the machine
off and back on again. If this persists,
contact your authorized Husqvarna
Viking retailer.
Expert assistance
Have your machine "tuned up"
regularly by your dealer. If you have
followed the preceding points and still
do not get satisfactory results, you
should contact the dealership where
you bought the machine. When the
machine is being checked, it is a great
help if it can be test sewn under as
similar conditions as possible as when
you used it.
Remember to take a sewing sample
along with you, preferably of the fabric
and with the thread you intend to use.
A sewing sample will often give much
better information than words.
Non-original parts and accessories
The warranty does not cover any
defect or damage caused by use of
non-original accessories or parts.
… 61 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna SCANDINAVIA 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna SCANDINAVIA 400 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info