518169
54
Zoom out
Zoom in
Previous page
1/60
Next page
52
Care of your Scandinavia 300
Trouble shooting
Always start by checking the
needle
Always start with a new needle as
soon as you discover that a stitch
is not what you expected. Test sew
on a scrap of the fabric you are
sewing. Check that you have chosen
the correct needle and see that it is
correctly inserted. See page 12.
Unattractive stitches
The thread tension is not correct. See
page 10. Make sure that the thread
is not catching. Certain thread spools
are unsuitable for spooling from the
horizontal spool pin. Try instead
with the vertical spool pin.
The machine may be incorrectly
threaded. Be sure to place spool
holders correctly.
The correct threading is shown on
page 6.
Wrong bobbin thread. It should be
of the same thickness as the upper
thread except for embroidery.
The needle breaks
The needle can strike against stitch
plate and break. Change the needle.
See page 12.
The upper thread breaks
Check the thread spool to see that it
has not caught in any way.
The needle eye may have sharp
edges which cut the thread. If so,
change the needle. See page 12.
The upper thread is incorrectly
threaded. See page 6.
The upper thread may have too
much tension. Refer to page 10.
The hole in the stitch plate may be
chipped and have sharp edges. We
recommend that you replace it.
The bobbin thread breaks
The bobbin thread may be
incorrectly threaded. See page 9.
The stitch plate hole is damaged. See
"Upper thread breaks".
Irregular thread tension
This may be due to poor quality
thread. When sewing with cotton
thread, increase the thread tension.
See page 10.
Irregular bobbin winding
The machine is not correctly
threaded for bobbin winding. See
page 8.
The fabric puckers
The upper thread tension is too
tight. See page 10 for correct thread
tension.
Use the correct presser foot as
recommended by the Infodisplay.
The machine does not feed the
fabric
The stitch length is too short.
Increase stitch length.
The feed teeth may be lowered.
Raise them by turning the dial to
. See page 12.
The feed teeth are full of dust and
dirt. Clean with the brush. See page
51.
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna SCANDINAVIA 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna SCANDINAVIA 300 in the language / languages: English as an attachment in your email.

The manual is 3,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info