518168
40
Zoom out
Zoom in
Previous page
1/44
Next page
38
Care of your Scandinavia 200
Trouble Shooting
Checking the Needle
Always start with a new needle as soon as
you discover that a stitch is not what you
expected. Test sew on a scrap of the fabric
you are sewing. Check that you have chosen
the correct needle and see that it is correctly
inserted.
Unattractive Stitches
The thread tension is not correct. Make
sure that the thread is not catching. Certain
thread spools are unsuitable for spooling
from the horizontal spool pin. Try instead
with the vertical spool pin. The machine
may be incorrectly threaded. Be sure to
place spool holders correctly.
Wrong bobbin thread. It should be of the
same thickness as the upper thread.
The Needle Breaks
The needle can strike against stitch plate and
break. Change the needle. Do not pull fabric
as you sew, let the machine feed.
The Upper Thread Breaks
Check the thread spool to see that it has
not caught in any way. The needle eye may
have sharp edges which cut the thread. If so,
change the needle.
The upper thread is incorrectly threaded.
The upper thread may have too much
tension.
The hole in the stitch plate may be chipped
and have sharp edges. We recommend that
you replace it.
The Bobbin Thread Breaks
The bobbin thread may be incorrectly
threaded. The stitch plate hole is damaged.
See "Upper thread breaks".
Irregular Thread Tension
This may be due to poor quality thread.
When sewing with cotton thread, increase
the thread tension.
The Machine Does Not Feed the Fabric
The stitch length is too short. Increase stitch
length.
The feed teeth may be lowered. Raise them
by turning the dial to
.
The feed teeth are full of dust and dirt.
Clean with the brush.
The Seam is Too Loose – Fabric Layers
Not Held Together
The thread tension is far too loose. Adjust
the thread tension.
Incorrect Stitch
If the machine does not sew the stitch
indicated by the display, it is possible that
the electronics have been disturbed in
some way, perhaps by a short power cut or
electrical disturbance.
Shut off the main switch, wait a few seconds
and try again. If the fault remains, contact
your dealer.
Machine Runs Sluggishly
Dirt or lint has built up under the stitch
plate. Remove the plate and brush clean
between the feed teeth and in the bottom
area.
Main motor does not work
The electronic overload protector may have
switched off. Shut off the main switch, wait
about a minute. Then turn on the machine.
Expert assistance
Have your machine "tuned up" regularly
by your dealer. If you have followed
the preceding points and still do not
get satisfactory results, you should
contact the dealer where you bought
the machine. When the machine is
being checked, it is a great help if it can
be test sewn under conditions that are
similar to when you used it.
Remember to take a sewing sample
along with you, preferably the fabric
and the thread you intend to use.
A sewing sample will often give much
better information than words.
Non-original Parts and Accessories
The warranty does not cover any defect
or damage caused by use of non-
original accessories or parts.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna SCANDINAVIA 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna SCANDINAVIA 200 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna SCANDINAVIA 200

Husqvarna SCANDINAVIA 200 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info