477570
65
Zoom out
Zoom in
Previous page
1/76
Next page
65
02239
1
2
3
TRANSAXLE GEAR SHIFT LEVER NEUTRAL
AD JUST MENT
The transaxle should be in neutral when the gear shift lever
is in neutral (N) (lock gate) position. The adjustment is preset
at the factory; however, if adjustment is needed, proceed as
follows:
Make sure transaxle is in neutral (N).
NOTE: When the tractor rear wheels move freely, the trans-
axle is in neutral.
Loosen adjustment bolt in front of the right rear wheel.
Position the gear shift lever in the neutral (N) position.
Tighten adjustment bolt securely.
NOTE: If additional clearance is needed to get to adjustment
bolt, move mower deck height to the lowest position.
EINSTELLUNG DES SCHALTHEBELS DES
DIFFERENTIALGETRIEBES
Das Differentialgetriebe muß sich in Leerlaufstellung be-
finden, wenn der Schalthebel in der Neutral-Stellung (N)
(Verschlußsperre) steht. Diese Einstellung wird bereits vom
Hersteller im Werk durchgeführt. Sollte es jedoch dennoch
erforderlich sein, weitere Einstellungen vorzunehmen, so muß
folgendermaßen vorgegangen werden:
Zunächst muß sichergestellt werden, daß sich das Dif-
ferentialgetriebe in Leerlaufstellung (N) befindet.
HINWEIS: Wenn die Hinterräder des Traktors frei beweglich
sind, ist das Getriebe immer in Leerlaufstellung.
Den vorne auf dem rechten Hinterrad befindlichen Ein-
stellbolzen lockern.
Nun den Schalthebel in die Leerlaufstellung (N) brin-
gen.
Den Einstellbolzen wieder fest anziehen.
HINWEIS: Falls eine größere Bewegungsfreiheit benötigt
wird, um an den Einstellbolzen zu gelangen, ist es ratsam,
die Mäherplattform in die niedrigste Stellung abzusenken.
REGLAGE DE LA POSITION NEUTRE (POINT
MORT) DU LEVIER DE CHANGEMENT DE VITESSE
DES BOITES MECANIQUES.
La boîte de vitesse mécanique doit se trouver au point mort
lorsque le levier de changement de vitesse se trouve dans
l'encoche de position neutre (N). Le réglage de la position du
levier est effectué en usine ; toutefois, un nouveau réglage peut
s'avérer nécessaire, procéder alors de la façon suivante:
Vérifier que la boîte de vitesse est au point mort.
REMARQUE : La boîte de vitesse est au point mort lorsque
les roues arrières du tracteur peuvent être manoeuvrées
librement.
Desserrer la vis de réglage (3) située à l'avant de la roue
arrière droite.
Positionner le levier de changement de vitesse dans
l'encoche de position neutre (N).
Resserrer à fond la vis de réglage (3).
REMARQUE : Mettre le carter de coupe en position basse
afin de dégager un peu plus d'espace pour effectuer ce
réglage.
1. Gear Shift Lever
2. Neutral Lock Gate
3. Adjustment Bolt
1. Steuerknüppel
2. Verschlussperre in Leerlaufstellung
3. Einstellbolzen
1. Levier de changement de vitesse
2. Encoche de position neutre (point mort)
3. Vis de réglage
6
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LT154 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LT154 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info