477570
34
Zoom out
Zoom in
Previous page
1/76
Next page
34
Turn the ignition key to “START position”.
NOTE!
Do not run the start motor more than 5 sec onds at once.
If the engine will not start, wait about 10 sec onds before
the next try.
Zündschlüssel auf “START” drehen.
HINWEIS!
Den Anlasser nicht jeweils länger als ca. 5 Sekunden betäti-
gen. Wenn der Motor nicht anspringt, vor dem nächsten An-
laßversuch ca. 10 Sekunden warten.
Amener la clé de contact sur la position "Démarrage"
("START").
REMARQUE!
Ne pas laisser tourner le démarreur plus de 5 secondes à
chaque fois. Si le moteur ne démarre pas immédiatement,
attendre une dizaine de secondes avant d'effectuer une
nouvelle tentative.
Ponga la llave de encendido en la posición de arranque
”START”.
NOTA!
No haga funcionar el motor de arranque más de unos 5
segundos a la vez. Si el motor no arranca, espere unos 10
segundos antes de hacer otra tentativa.
Girare la chiave su “START”.
NOTA!
Non inserire il motorino di avviamento per più di 5 secondi
per volta. Se il motore non parte attendere una decina di
secondi prima di riprovare.
Draai de startsleutel naar “START”-positie
N.B.!
Laat de startmotor niet langer dan ca 5 sek. per keer draaien.
Als de motor niet start, wacht dan ca 10 sek voordat u vol-
gende poging doet.
Let the ignition key return to the ”ON” position when the
engine has started and push in the choke control as soon
as the engine is running smoothly. Push the gas control to
the re quired speed. For cutting: full gas.
Nach Anspringen des Motors den Zündschlüssel in die
Stellung “ON” zurückgehen lassen. Den Kaltstarthebel
zurückschieben, so daß der Motor gleichmäßig arbeitet.
Den Gashebel auf die gewünschte Motordrehzahl stellen.
Bei Mähen: Vollgas.
Laisser ensuite la clé revenir sur sa position "On" lorsque le
moteur a démarré et repousser la commande de starter dès
que le moteur tourne régulièrement. Amener la commande
des gaz à la position correspondante au régime moteur désiré.
Pour la tonte, positionner cette manette dans l'encoche prévue
pour obtenir le régime optimal pour la tonte (accélération
maximale du moteur).
Dejar que la llave de encendido vuelva a la posición “ON”
cuando ha arrancado el motor e introducir el estrangulador
tan pronto como el motor funcione con regularidad. Ponga
el acelerador en la posición deseada. Al cortar, a plenos
gases.
Dopo l’avviamento, riportare la chiave su “ON”. Regolare il gas
sul regime desiderato. Per il taglio: massimo regime “F”.
Draai de startsleutel terug in “ON”-posotie, wanneer de motor
is gestart en schuif de choke in zordra de motor gelijkmatig
loopt. Schuif de gashendel naar het gewenste toerental. Bij
maaien: vol gas.
0
2
9
2
7
5
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LT154 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LT154 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info