518123
54
Zoom out
Zoom in
Previous page
1/60
Next page
54 Instruction book Lily 555/545
Fault-fi nding
The balance can be set between -5
to +5. The balance indication on
the dis-play will change in steps fo
each touch. When you select an-
other stitch, the display goes back
to show the sitch length indication.
The machine always retains the last
made balance setting.
Balance setting for buttonhole
Balance can only be set if a button-
hole is selected. Press the buttons
and until the letters BAL are
ashing to the left on the display. In
place of the stitch length indication
a balance indication is shown. When
you wish to increase the density
of the right column, press stitch
length button (-). When you wish
to decrease the density, press stitch
length button (+).
Machine runs sluggishly
Dirt or lint has built up under the
stitch plate. Loosen the plate and
brush clean between the feed teeth
and in the bottom area. See page 52.
Incorrect stitch
If the machine does not sew the
stitch indicated by the display, it is
possible that the electronics have
been disturbed in some way, per-
haps by a short power cut or electri-
cal disturbance. Shut off the main
switch, wait a few seconds and try
again. If the fault remains, contact
your dealer.
The stitch is too loose - fabric
layers not held together
The thread tension is far too loose.
Page 14 shows how to adjust the
thread tension.
The machine does not feed the
fabric
The stitch length is too short. In-
crease stitch length.
The feed teeth may be lowered.
Raise them by turning the dial to
. See page 16.
The feed teeth are full of dust and
dirt. Clean with the brush. See page
52.
Fault-fi nding
Main motor does not work
The electronic overload protector
may have switched off. Shut off the
main switch, wait about a minute.
Then switch on the machine.
Expert assistance
Have your machine "tuned up"
regularly by your dealer. If you have
followed the preceding points and
still do not get satisfactory results,
you should contact the dealer where
you bought the machine. When the
machine is being checked, it is a
great help if it can be test sewn un-
der as similar conditions as possible
as when you used it.
Remember to take a sewing sample
along with you, preferably of the fa-
bric and with the thread you intend
to use.
A sewing sample will often give
much better information than words.
Non-original Parts and
Accessories
The warranty does not cover any
defect or damage caused by use of
non-original accessories or parts.
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LILY 555 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LILY 555 in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info