609918
49
Zoom out
Zoom in
Previous page
1/51
Next page
PERFORMANCE
PROBLEMS
Whenever
sewing
diffi
ulties
are
encountered,
review
the
section
of
the instruction
book
that
explains
about
the
operation
you
are
performing
to
make
sure
that
you
are
using
the machine
correctly.
If
the
problem
persists.
the
fol
lowing
cheek
list
may
help
you
to
correct
it.
If
you
still
have
difficulties,
contact
your
nearest
authorized
service
center.
Needle
is
bent,
or
tip
of
needle
is
broke
ii
Needle
is
incorrectly
installed.
Thread
is
incorrectly
threaded.
Presser
toot
pressure
is
too
weak.
lncorre
t
type
0)
needle
is
being
riced.
Thread
tension
is
incorrect.
Thread
is
incorrectly
threaded.
3.
Thread
breaks.
Thread
is
inc
orrectlv
threaded.
4.
Material
is
puc
kered.
Install
correctly.
Thread
correctly.
_________
Turn
the
presser
foot
pressure
adjustment
dial
to
the
right
to
Lnrease
the_pressure.
Use
a
SCHMETZ
130/70Th
Refer
to
“Thread
tension
adjustment”.
Thread
correctly.
Thread
correctly.
Refer
to
“Differential
feed”.
Turn
the
presser
foot
pressure
adjustment
dial
to
the
right
to
increase
the pressure.
Set
the
stitch
length
correctly;
Replace
with
a
new
needle.
Install
correctly.
Do
not
press
or
pull
the
material
too
strongly
while
sewing.
Probleni
Cause
1.
Skipped
stitches
2.
Stitch
tension
is
incorrc’(
t.
Remedy
Replace
with
a
new
needle.
Page
10-12
10-12
13-24
39
Stitch
width
is
inappropriate.
Refer
to
“Stitch
width
and
cutting
width
37
fine-tune
adjustment”.
31
-34
13-24
13-24
F
Thread
is
hooked
up
incorrectly.
Check
that
thread
is
not
hooked
on
thread
13-19
guide.____________
Thread
tension
is
too
strong.
Refer
to
“Thread
tension
adjustment”.
31-34
Needle
is
bent,
or
tip
of
needle
is
Replace
with
a
new
needle,
10-12
broken.
Needle
isicorrectlynistalled.
Install
correctly.
10-12
7hread
tension
is
too
strong.
lf
sewing
with
thin
material,
reduce
the
32
tension
as
necessary.
Presser
foot
pressure
is
too
strong.
Turn
the
presser
loot pressure
adjustment
39
dial
to
the
left
to
decrease
the
pressure.
Stitch
width
is
inappropriate.
Refer
to
“Stitch
width
and
cutting
width
37
fine-tune
adjustment”.
Thread
is
incorrectly
threaded,
or
thread
Thread
correctly.
13-19
is
hooked
up
incorrectly.
Differential
feed
adjustment
is
incorrect.
5.
Mat’
ial
does
not
feed.
6.
Needle
breaks.
Presser
foot
pressure
is
too
weak.
Stitch
length
is
not
appropriate
for
the
material.
Needle
is
bent,
or
tip
of
needle
is
broken.
Needle
set
screw
is
loose,
or
needle
is
incorrectly
installed,
Material
is
being
pulled
too
tightly.
38
-39
36
10-12
10-12
29
7.
Sewing
machine
The
power
cord
is
unplugged
from
the
Plug
in
the
power
cord,
or
turn
the
switch
29
does
not
oper-
power
supply,
or
the
power
switch
is
on.
ate. not
switcher)
on.
Presser
foot
is
raised
imodels
with
LCD).
Lower
the
presser
foot.
29
8.
Nothing
appears
C
ontrast
adjustment
dial
is
incorrectly
Turn
the
LCD
contrast
adjustment
dial
up-
1,
3
on
the
LCD
positioned.
csard.
(models
with
LCD.
-44-
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskylock 1002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskylock 1002 in the language / languages: English as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info