Manual Husqvarna CTH184T (page 22 of 112) (English, German, Dutch, French, Italian, Spanish)

477578

Zoom out

Zoom in

1/112

• From the rear of the tractor, slide the lower clevis assembly

(12) onto the right side bagger support tube (10). Line up the

center hole (13) on upper bracket with the hole in the bagger

support tube (10) and secure lower clevis assembly (12) with

clevis pins (14) and clips (15).

• Install the actuator (16) as shown. Use the spacers (17) to

center the actuator (16) between both the upper and lower

brackets and secure with clevis pins (18) and clips (19).

TO INSTALL BAGGER SPRING LATCH

The bagger spring latches are located on the back plate (1),

one in each of the bottom corners.

Before installing, tractor engine must be shut off and parking

brake engaged.

• Install each bagger spring latch with the loop end (2) down

and facing towards the bagger assembly.

• Place the mounting bolt (3) through the backplate. Place

curved end of the bagger spring latch onto mounting bolt (3)

and secure with nut (4) as shown. Tighten firmly.

BAGGER SPRING LATCH ADJUSTMENT

If the bagger assembly height is adjusted, it may be necessary

to adjust the bagger spring latch. To adjust, remove the nut (4)

and move the bagger spring latch to the appropriate hole in the

backplate (1), ensuring the bagger assembly will be securely

closed. Retighten nut securely.

NOTE: The bottom of the bagger assembly should contact the

loop end so that it is held securely when closed.

TO INSTALL BAGGER FULL LEVER/EXTENSION

Before installation or adjusting, tractor engine must be shut off

and parking brake engaged.

• Remove center discharge chute. (See "To Remove Center

Chute" in section 6 of this manual.)

• Remove bolt (1). Place lever (2) into slot and reinstall bolt

(1). Adjust as needed.

TO ADJUST BAGGER FULL LEVER/EXTENSION

Slide bagger full extension (3) to the desired position.

• For the heaviest/wet grasses, slide extension all the way in.

• For the lightest/driest grasses, pull extension all the way out.

• Route cable assembly (20) between the lower clevis assem-

bly (12) and along bagger support tube (10), and connect the

cable assembly (20).

• Using the switch (21) on the right side fender, fully extend

the actuator (16). Secure any excess cable assembly to

the bagger support tube (10) with the zip ties (22). Retract

the actuator (16) and check to ensure there are no snags or

binds in the cable assembly (20).

• Install the bagger assembly.

NOTE: Both cross tubes (23) on the bagger support weldment

need to be placed onto the top support assemblies (24). Extend-

ing the actuator slightly will help make installation easier. Once

installed, adjust bagger assembly as needed. (See "To Adjust

Bagger" in this section of the manual.)

Gibt's für den cth184t eine Abbildung von den Bedienelementen und deren Bedeutung Submitted on 26-2-2023 at 10:59
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH184T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna CTH184T Manual

Product: