477581

Husqvarna CTH182T Manual

81
Zoom out
Zoom in
Previous page
1/96
Next page
81
6
Replacement of drive belt
1. Dismantle the cutting unit as described pre vi ous ly.
2. Pull apart the contact for the cable to the elec tri cal con-
nection (1).
3. Dismantle the motion restrainer for the clutch (2).
4. Engage the parking brake and work off the belt upwards
from the pulley (3), the clutch pul ley (4).
5. Push the belt up between two fan blades and rotate the
fan clockwise until the belt comes loose (5).
6. Take off the belt from the engine pulley (6).
Auswechsein des Treibriemens
1. Mähaggregat ausbauen.
2. Den Kabelstecker für den elektrischen Anschluß anziehen
(1).
3. Bewegungsbegrenzer für die Kupplung (2).
4. Feststellbremse ansetzen und den Riemen vom Laufrad
(3), dem Kupplungsriemenrad (4).
5. Den Reimen zwischen zwei Lüfterblättern einführen und
den Lüfter nach links drehen, bis der Riemen frei geht (5).
6. Riemen vom Riemenrad des Motors (6).
Remplacement de la courroie d'entraînement
1. Désaccoupler le carter de coupe du tracteur comme
indiqué précédemment. (Chapitre 6.6).
2. Débrancher le connecteur (1) du câble d'alimentation de
l'embrayage électromagnétique.
3. Démonter le limiteur de débattement de l'embrayage
électromagnétique (2).
4. Serrer le frein de stationnement et retirer la courroie
d'entraînement de la poulie de guidage (3), puis de la
poulie de tension (4).
5. A l'arrière, faire passer la courroie entre deux pales de la
turbine de refroidissement (5) et faire tourner à la main la
turbine dans le sens inverse des aiguilles d'une montre
pour dégager la courroie.
6. Enfin, dégager la courroie de la poulie motrice (6).
Cambio de correa propulsora
1. Desmontar el equipo de corte del tractor.
2. Despiezar el contacto de cable de la conexión eléctrica (1).
3. Desmontar el limitador de movimientos del acoplamiento
(2).
4. Aplicar el freno de estacionamiento y tirar hacia arriba
de la correa para sacarla de la rueda libre (3), de la
acoplamiento (4).
5. Introducir la correa entre dos aspas del ventilador y hacer
girar éste a izquierdas hasta que queda libre la correa (5).
6. Quitar después la correa de la polea del motor (6).
Sostituzione della cinghia di trazione
1. Smontare il tagliaerba.
2. Staccare il cavo dal contatto elettrico (1).
3. Smontare il limitatore della frizione (2).
4. Inserire il freno di parcheggio e staccare la cinghia dalla
puleggia (3), da quella della frizione (4).
5. Passare la cinghia tra due pale della ventola e ruotare la
ventola in senso antiorario fino a che la cinghia non sia
libera (5).
6. Togliere la cinghia dalla puleggia del motore (6).
Vervangen van de aandrijfriem
1. Verwijder de maaikast van de tractor.
2. Trek de contacten voor de kabel van de electrische kop-
peling (1).
3. Demonteer de bewegingsbegrenzer voor de koppeling (2).
4. Trek de handrem aan en trek de riem omhoog van het
loopwiel (3), de koppelingswielschijf (4).
5. Leid de riem tussen twee ventilatorbladen door en draai
de ventilator tegen de klok in tot de riem vrij komt (5).
6. Haal daama de riem van de wielschijf van de motor (6).
Assemble in the reverse order to dismantling. Check that
the belt lies inside all the belt guides. Use original belts only
when replacing!
Der Einbau erfolgt in umgekehrter Reihenfolge. Prüfen,
daß der Riemen innerhalb aller Riemenführer liegt. Beim
Auswechseln nur Originalriemen verwenden!
La mise en place d'une courroie se fait dans l'ordre inverse
de la dépose. Vérifier que la courroie est bien positionnée
devant tous les guides de courroie. Utiliser exclusivement
une courroie d'origine lors d'un remplacement!
El montaje se hace en el orden inverso al desmontaje. Con-
trolar que la correa se halla por dentro de todas las guías.
Montar únicamente correas originales!
Il montaggio avviene in ordine inverso. Controillare che
la cinghia sia dietro ai guida-cinghia. Usare solo cinghie
originali!
De montering vindt in omgekeerde volgorde plaats als de de-
montering. Controleer of de snaar binnen alle riem-geleiders
ligt. Gebruik uitsluitend originele riemen bij vervanging!
01511
2
1
6
4
3
5
… 81 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna CTH182T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH182T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info