477580

Husqvarna CTH163T Manual

21
Zoom out
Zoom in
Previous page
1/96
Next page
21
2
TO ASSEMBLE BAGGER
• Unfold bag and stand right side up.
• Feed front bagger frame (1) up through fabric loops at each
side of bagger.
• Snap bottom of front bagger frame (1) into snap feature at
front of bagger bottom.
• Slide bagger fabric loop (2) segments at the ends of bag
onto top bagger frame tubing.
• Uninstall two (¼”-20 x 1.15”) hex bolts (3) from the front of
top frame.
• Reinstall the two (¼”-20 x 1.15”) hex bolts (3) through holes
at top of the front bagger frame and thread into nuts inside
the tubing of top bagger frame.
• Uninstall (1/4”-20) lock nuts (4) at bottom of front bagger frame.
• Unfold cross braces (5) and attach to carriage bolts at bottom
corners of front bagger frame.
• Reinstall (1/4”-20) lock nuts (4) and tighten until fully seated.
• Install corner support brackets.
• Place the bottom of the corner support bracket (6) into
the corner of the bagger bottom.
• Push corner support bracket into the corner until the upper
hole is aligned with the hole in the upper bar.
• Secure corner support bracket to the upper bar (7) with
fastener (8).
• Push the bottom of the corner support bracket (6) forward
as shown to secure it in the proper position.
• Repeat procedure on other side.
• Remove clevis pin (9) and retainer spring (10) from bagger
handle (11).
• Slide bagger handle (11) down through bagger cover and
frame upper weldment holes.
• Reinstall clevis pin (9) through hole at bottom of bagger
handle and slide retainer spring (10) into hole at the end of
the clevis pin until it locks into place
3
2
1
5
6
7
8
4
11
10
9
HORIZONTAL ADJUSTMENT
• Loosen nuts on carriage bolts (3) to allow the adjustment plate
(4) to slide forward or rearwards. Move as needed. Retighten
nuts securely, locking the adjustment plate in its new position.
• Repeat on opposite side.
1
2
A
3
4
TO ADJUST HANGER BRACKETS
The tractor comes from the factory with the bagger pivot bracket
preset in a fixed position. If necessary, this position can be adjusted
to maintain a consistent gap (A) between the fender and the bag-
ger assembly top. An ideal gap is approximately 0.2” (5.1mm).
NOTE: As desired, the hanger bracket on either side can be
adjusted in this manner.
• Remove bagger assembly.
NOTE: ADJUST ONLY ONE SIDE AT A TIME.
VERTICAL ADJUSTMENT
• Loosen nuts on carriage bolts (1) to allow the adjustment plate
(2) to slide up or down. Move as needed. Retighten nuts
securely, locking the adjustment plate in its new position.
• Repeat on opposite side.
• Readjust if necessary.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna CTH163T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH163T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info