477560

Husqvarna CT154 Manual

25
Zoom out
Zoom in
Previous page
1/96
Next page
25
2
• Den Gabelstift (9) und die Federklammer (10) vom Sackgriff
(11) entfernen.
• Den Sackgriff (11) durch die Sackabdeckung und das
Schweißteil des oberen Rahmens nach unten schieben.
• Montieren Sie die Eckhalterungen.
• Setzen Sie die Unterseite der Eckhalterung (6) in die Ecke
der Fangkorbunterseite ein.
• Drücken Sie die Eckhalterung in die Ecke hinein, bis die obere
Öffnung auf die Öffnung in der unteren Leiste ausgerichtet ist.
• Sichern Sie die Eckhalterung an der oberen Leiste (7) mit
Befestigungselement (8).
• Schieben Sie die Unterseite der Eckträgerhalterung (6)
wie abgebildet nach vorn, um sie in der richtigen Position
zu sichern.
• Wiederholen Sie diesen Vorgang auf der anderen Seite.
5
6
7
8
4
MONTAGE DER GRASFANGBOX
• Den Beutel entfalten und mit der rechten Seite nach oben
aufstellen.
• Den vorderen Sackrahmen (1) durch die Schlaufen auf
beiden Seiten des Sacks ziehen.
• Den unteren Teil des vorderen Sackrahmens (1) in den
Schnapper auf dem Boden des Sacks einrasten.
• Die losen Sackschlaufen (2) an den beiden Sackenden auf
das Rohr des oberen Rahmens schieben.
• Zwei Sechskantschrauben (3) (¼”-20 x 1.15”) auf der
Vorderseite des oberen Rahmens lockern.
• Zwei Sechskantschrauben (3) (1/4”-20 x 1,15”) durch die
Löcher auf der Oberseite des Frontrahmens schieben und in
die Muttern im Inneren des Rahmenrohrs schrauben.
3
2
1
• Zwei Sechskantmuttern (4) (1/4”-20) am Boden des vorderen
Sackrahmens lösen.
• Die Querstreben (5) aufklappen und an den Karosser-ie-
schrauben an den unteren Ecken des vorderen Sackrah-
mens anbringen.
• Die Sicherungsmuttern (4) (1/4”-20) einsetzen und bis zum
Anschlag festziehen.
TO ADJUST BAGGER FULL LEVER/EXTENSION
• Before adjusting, tractor engine must be shut off and parking
brake engaged.
Slide bagger full extension to the desired position (1).
• For the heaviest/wet grasses, slide extension all the way in.
• For the lightest/driest grasses, pull extension all the way out.
1
TO INSTALL BAGGER SPRING LATCH
The bagger spring latches are located on the back plate (1),
one in each of the bottom corners.
• Before installing, tractor engine must be shut off and parking
brake engaged.
• Install each bagger spring latch with the loop end (2) down
and facing towards the bagger assembly.
• Place the mounting bolt (3) through the curved end of the
bagger spring latch, through the back plate, and secure with
nut (4) as shown. Tighten firmly.
• The bottom of the bagger assembly should contact the loop
end so that it is held securely when closed.
2
1
3 4
NOTE: If the bagger assembly height is adjusted, it may be
necessary to adjust the bagger spring height to keep the bagger
assembly securely closed. To adjust, loosen the nut (4) enough
to allow the bagger spring latch to move. Slide the bagger spring
latch up or down as needed, ensuring the bagger assembly will
be securely closed. Retighten nut securely.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna CT154 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CT154 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 10,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info