733900
6
Zoom out
Zoom in
Previous page
1/8
Next page
For more information and instructions, read the complete Operators manual on the Husqvarna
website (www.husqvarna.com).
1. PLACEMENT OF AND CONNECTING THE CHARGING STATION
1. Place the charging station with a lot of open space in front of the charging station and on a relatively horizontal surface.
2. Connect the power supplys low voltage cable to the charging station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
4. Place the product in the charging station to charge the battery while the boundary wire is laid. Start the product.
2. PLACEMENT OF THE BOUNDARY WIRE AND THE GUIDE WIRE
1. Lay the boundary wire so that it forms a loop around the work area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles.
4. For minimum distance to obstacles and islands, see illustration (number 5).
3. CONNECTING THE BOUNDARY WIRE AND THE GUIDE WIRE
1. Narrow passages in the yard make it dicult for the product to nd the charging station. The product can be lead to remote
areas using the guide wire. The guide wire also helps the product to quickly nd the charging station.
2. Lay the guide wire under the charging station and at least 2 m / 7 ft straight out from the front edge of the charging station.
3. Open the connectors and lay the wire ends in the recesses on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut 1-2 cm / 0.4-0.8 in. above the connectors.
6. Press the boundary connectors onto the contact pins, marked AL (left) and AR (right), on the charging station. It is important
that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the guide connector to the contact pin marked G1 on the charging station. Additional guides the similar way.
4. CONNECTING THE GUIDE WIRE TO THE BOUNDARY WIRE
1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with a
pair of pliers.
STARTING AND STOPPING
STARTING
1. Push the START button.
2. Push the jog wheel to conrm and the product starts.
STOPPING
Push the STOP button.
ADJUSTING THE PRODUCT TO SUIT THE SIZE OF YOUR LAWN
Adjust the mowing time to suit your yard using the Schedule function. The product cuts approximately 146 m² / 1570 ft² per hour
and day. For example, if your yard comprises 1200 m² / 12900 fof grass, the product should work 8 hours a day.
MAINTENANCE
1. The product must be turned o before any maintenance is done, such as cleaning or replacing the blades. The product is
disabled when the LED indicator lamp at the jog wheel is not lit. Replace the blades regularly for the best mowing result.
2. Never use a high-pressure washer or even running water to clean the product. Never use solvents for cleaning.
3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
EN
P25_QG_1140537_435X_AWD_2020.indd 6P25_QG_1140537_435X_AWD_2020.indd 6 2020-04-17 14:01:032020-04-17 14:01:03
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna AUTOMOWER 435X AWD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna AUTOMOWER 435X AWD in the language / languages: English, Italian as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna AUTOMOWER 435X AWD

Husqvarna AUTOMOWER 435X AWD User Manual - English - 68 pages

Husqvarna AUTOMOWER 435X AWD Quick start guide - German - 8 pages

Husqvarna AUTOMOWER 435X AWD User Manual - German - 72 pages

Husqvarna AUTOMOWER 435X AWD Quick start guide - Dutch - 8 pages

Husqvarna AUTOMOWER 435X AWD User Manual - Dutch - 72 pages

Husqvarna AUTOMOWER 435X AWD Quick start guide - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info