734125
4
Zoom out
Zoom in
Previous page
1/360
Next page
loaded stop switch and can be started by low speed
and force on the starter handle, even small children
under some circumstances can produce the force
necessary to start the product. This can mean a risk
of serious personal injury. Therefore remove the
spark plug cap when the product is not under close
supervision.
Store the product out of reach of children.
Never use the product if you are tired, if you have
drunk alcohol, or if you are taking medication that
could affect your vision, your judgement or your
coordination.
Never use a product that is faulty. Carry out the
checks, maintenance and service instructions
described in this manual. Some maintenance and
service measures must be carried out by trained and
qualified specialists. Refer to instructions under the
heading Maintenance.
Never use a product that has been modified in any
way from its original specification.
Safety instructions for operation
WARNING: Read the warning instructions
that follow before you use the product.
Never use the product in extreme weather conditions
such as severe cold, very hot and/or humid climates.
Faulty blades can increase the risk of accidents.
Ensure that no people or animals comes closer than
15 m / 50 ft while you work.
Observe your surroundings and make sure that there
is no risk of people or animals coming into contact
with the cutting equipment.
Inspect the working area. Remove any objects that
could be thrown out.
Always ensure you have a safe and stable working
position.
Never leave the product unsupervised with the motor
running.
Make sure that your hands and feet do not come
near the cutting unit when the engine is running.
If anything jams in the blades while you are working,
switch off the engine and wait until it has stopped
completely before cleaning the blades. Disconnect
the spark plug cap from the spark plug.
When the engine is switched off, keep your hands
and feet away from the cutting unit until it has
stopped completely.
Watch out for stumps of branches that can be thrown
out during cutting.
Listen out for warning signals or shouts when you
are wearing hearing protection. Always remove your
hearing protection as soon as the engine stops.
Never work from a ladder, stool or any other raised
position that is not fully secured.
Always use both hands to hold the product. Hold the
product in front of your body.
If any foreign object is hit or if vibrations occur stop
the product immediately. Disconnect the spark plug
cap from the spark plug. Check that the product is
not damaged. Repair any damage.
Ensure that the spark plug cap and ignition lead are
undamaged to avoid the risk of electric shock.
Check that all nuts and screws are tight.
Make sure the gearbox is lubricated correctly. Refer
to
To lubricate the gear housing on page 12
.
The gearbox gets hot when the product has been in
use. To avoid burning yourself do not touch the
gearbox.
All covers and guards must be fitted before starting.
If the blades get stuck, they can be loosened by
sticking the combination wrench into the gearbox.
Stick the combination wrench into the gearing and
turn it back and forth. Refer to
To examine the
blades on page 12
.
The transport guard should always be fitted to the
cutting unit when the product is not in use.
Personal protective equipment
WARNING: Read the warning instructions
that follow before you use the product.
Always use approved personal protective equipment
when you use the product. Personal protective
equipment cannot fully prevent injury but it
decreases the degree of injury if an accident does
occur. Let your dealer help you select the right
equipment.
Use approved hearing protection that provides
adequate noise reduction. Long-term exposure to
noise can result in permanent hearing impairment.
Use approved eye protection. If you use a visor, you
must also use approved protective goggles.
Approved protective goggles must comply with the
ANSI Z87.1 standard in the USAs or EN 166 in EU
countries.
Use gloves when necessary, for example when you
attach, examine or clean the cutting equipment.
4
905 - 001 - 05.02.2020
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 522HSR75X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 522HSR75X in the language / languages: All languages as an attachment in your email.

The manual is 3,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info