Manual Husqvarna 135 (page 27 of 420) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

477601

Zoom out

Zoom in

1/420

MAINTENANCE

English – 27

1154580-38 Rev.1 2011-12-05

assemble the drive disc spring, drive disc and the bolt

in the centre of the pulley. Carry the starter cord

through the hole in the starter housing and the starter

handle. Tie a good knot on the starter cord.

(98)

Tensioning the recoil spring

• Hook the starter cord in the notch in the pulley and

turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned at least a

further 1/2 turn when the starter cord is pulled all the

way out.

(99)

Stretch the line with the handle. Move your thumb and

release the line. See the ﬁgure below.

(99)

Replacing the return and drive springs

Recoil spring (A)

• Lift up the starter pulley. See instructions under the

heading Changing a broken or worn starter cord.

Remember that the recoil spring is coiled under

tension in the starter housing.

• Remove the cassette with the recoil spring from the

star

ter.

• Lubricate the recoil spring with light oil. Fit the

cassette with recoil spring in the starter. Fit the starter

pulley and tension the recoil spring.

Drive disc spring (B)

• Undo the bolt in the centre of the pulley and remove

the drive disc and the drive disc spring.

• Replace the drive disc spring and ﬁt the drive disc

above the spring.

(100)

Fitting the starter

• To ﬁt the starter, ﬁrst pull out the starter cord and place

the starter in position against the crankcase. Then

slowly release the starter cord so that the pulley

engages with the pawls.

• Fit and tighten the screws that hold the starter.

Air ﬁlter

The air ﬁlter must be regularly cleaned to remove dust and

dirt in order to avoid:

• Carburettor malfunctions

• Starting problems

• Loss of engine power

• Unnecessary wear to engine parts.

• Excessive fuel consumption.

• Remove the air ﬁlter after taking off the air ﬁlter cover.

When reﬁtting mak

e sure that the air ﬁlter seals tightly

against the ﬁlter holder. Clean the ﬁlter by brushing or

shaking it.

(101)

The ﬁlter can be cleaned more thoroughly by washing it in

water and detergent.

An air ﬁlter that has been in use for a long time cannot be

cleaned completely. The ﬁlter must therefore be replaced

with a new one at regular intervals.

A damaged air ﬁlter

must always be replaced.

A HUSQVARNA chain saw can be equipped with different

types of air ﬁlter according to working conditions, weather,

season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is inﬂuenced by:

• Incorrect carburettor adjustment.

• An incorrect fuel mixture (too much or incorrect type of

oil).

• A dirty air ﬁlter.

These factors cause deposits on the spark plug

electrodes

, which may result in operating problems and

starting difﬁculties.

If the machine is low on power, difﬁcult to start or runs

poor

ly at idle speed: always check the spark plug ﬁrst

before taking any further action. If the spark plug is dirty,

clean it and check that the electrode gap is 0,5 mm. The

spark plug should be replaced after about a month in

operation or earlier if necessary.

(102)

Note! Always use the recommended spark plug type! Use

of the wrong spark plug can damage the piston/cylinder.

Check that the spark plug is ﬁtted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use

the special grease gun and a good quality bearing grease.

(103)

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft.

This needle bearing must be lubricated regularly.

When lubricating, remove the clutch cover by loosening

the two bar nuts. Lay the saw on its side with the clutch

drum upwards.

Lubrication involves engine oil dripping into the centre of

the clutch dr

um as it rotates.

(104)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 135 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna 135 Manual

Product: