622640
4
Zoom out
Zoom in
Previous page
1/24
Next page
PROMIX400U2
V. 02 – 09/03/2012 4 ©Velleman nv
Always begin with the master faders, volume controls and the amplifier volume at minimum position.
Gradually turn up the volume after connection is completed.
Use the controls with restraint. Rapid movements may damage the speakers due to amplifier clipping.
Use the original packaging if the device is to be transported.
Keep this manual for future reference.
4. Features
outputs: 2 Master (XLR and RCA), 1 Rec (RCA) and booth monitor output (RCA)
inputs: 2 Phono (RCA), 4 Line (RCA) and 1 MIC (Combi), USB
with Digital Signal Processor (DSP) effects and fader start control
trim: gain for each input channel
peak level meter: allows the user to instantly determine the source input condition for each channel
talk over: mutes -14dB all levels apart from the microphone MIC1
cross fader curve: choose from two types of cross fader start-up options
headphone monitor balance between cue and master out
freely assignable long life TCT cross fader (45mm) with adjustable curve
extra LED display per channel for pre-listening signal
gain control with 3-fold sound control (+12/-26dB) per channel
3-fold sound control (+12/-26dB) for microphone
CUE on and off switch for each channel
cue-split function: the cue signal is sent to one side of the headphones and the output-signal to the
other side.
5. Overview
Refer to the illustrations on page 2 of this manual.
1 power switch: turn the mixer on or off.
2
3-pin XLR connection for main microphone (not included)
MIC LEVEL: adjust the microphone input level
HI/LOW: microphone equalizer
3
Input channel controls (CH-1 … CH-4)
Input selector switches:
Channel 1-2: LINE or PHONO. Set to PHONO if a turntable (not incl.) is connected to the input;
otherwise set to LINE.
Channel 3: LINE or USB. Set to USB if an input device is connected via the USB port [24]; otherwise
set to LINE.
Channel 4: LINE or MIC. Set to MIC if a microphone (not incl.) is connected to the input; otherwise
set to LINE.
TRIM: adjust the input signal level
HI/MID/LOW: channel equalizer
Peak level meter
4
Master channel
LED meter: indicates the master output level
5
TALK OVER: press this button to decrease the sound level for everything other than the main
microphone to 14dB. Press again to restore original status.
6
CUE: press this button to monitor the channel with headphones. You can select multiple channels at
once, including the master channel and the DSP effects. Press again to cancel the selection.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HQ Power PROMIX400U2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HQ Power PROMIX400U2 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info