661664

Hozelock 2702 AC sensor Manual

3
Zoom out
Zoom in
Previous page
1/16
Next page
AC sensor
The AC Sensor is a moisture sensitive switch designed to work
with the AC Pro water computer. It will stop the watering of all
p
rograms set on the water computer when rain falls. The
quantity of rain required to stop the watering can be adjusted on
the AC Sensor.
M
ount the AC sensor so that it is exposed to the same rain,
wind and sun as your plants.
The AC sensor should not be positioned where it could be
a
ffected by anything other than rain. E.g. sprinkler, hose
pipe watering, leaking gutter etc.
Connect to the water computer.
Push the connector into the socket found at the bottom of the
w
ater computer (underneath the Hozelock logo). Make sure
you connect the plug the right way around, taking care that
you don’t bend the pins on the water computer (see Fig.1)
Check the Connection.
Depress the spindle on the top of the AC Sensor until you hear
a click (see Fig.2). Hold for up to 1 minute or until the screen
on the water computer displays: “watering paused by rain
sensor”
Mount the timer in a suitable location.
i) On guttering: use the wing nut and bolt to clamp (see Fig.3)
ii) On a fence or wall: use the screws and plugs provided to
mount the plastic bracket, then slot the AC Sensor in position
(see Fig.4)
Setting the rainfall measurement.
The AC Sensor can be adjusted to vary the point at which rain
will suspend the watering program. This point is adjustable
between 3mm and 25mm (of rain). To adjust, rotate the yellow
cap and select the required depth (see Fig.5)
Setting the reset/drying-off time.
There is an adjustment capability on the AC Sensor that will
change the time required for the rain sensor to “dry off” and
there by resetting itself so it can detect rain again.
Turn the vent ring to expose the ventilation hole (see Fig.6).
This will decrease the reset time. Covering the vent hole will
increase the reset time.
If you have any further problems with your AC Sensor, please
contact Hozelock customer services.
Hozelock Limited
Midpoint Park, Birmingham. B76 1AB.
Tel : +44 (0)121 313 1122
Internet : www.hozelock.com
Email : info@hozelock.com
AC sensor
Le AC Sensor est un interrupteur sensible à l’humidité qui a été
conçu pour fonctionner avec le programmeur d’eau AC Pro. Il
arrête l’ensemble des programmes d’arrosage lorsque la pluie se
met à tomber. La quantité de pluie nécessaire pour arrêter
l’arrosage peut être réglée sur le AC Sensor.
Monter le capteur CA de manière à ce qu’il soit exposé à la
même quantité de pluie, de vent et de soleil que vos
plantes.
Le capteur CA doit être positionné de manière à ne pas être
affecté par d’autres éléments que la pluie, par ex. par un
goutteur, un tuyau d’arrosage, une gouttière qui fuit etc.
Raccorder au programmeur d’eau.
Enfoncer le connecteur dans la prise qui se trouve à l’extrémité
inférieure du programmeur d’eau (en dessous du logo
Hozelock). S’assurer de bien mettre la prise dans le bon sens,
en prenant soin de ne pas plier les broches sur le programmeur
d’eau (voir Fig.1)
Vérifier la connexion
Appuyer sur l’axe au-dessus du AC Sensor jusqu’à ce que vous
entendiez un déclic (voir Fig.2). Maintenir enfoncé pendant 1
minute maximum ou jusqu’à ce que l’écran du programmeur
affiche : “Le capteur de pluie a mis l’arrosage en pause”
Monter le minuteur dans un endroit approprié.
i) Sur une gouttière : Utiliser l’écrou à oreille et le boulon pour la
fixation (voir Fig.3)
ii) Sur une barrière ou un mur : Utiliser les vis et les chevilles
fournies pour monter l’applique en plastique puis y glisser le
AC Sensor en position (voir Fig.4)
Le réglage pour la pluie.
Le AC Sensor peut être réglé pour choisir la quantité de la
pluie qui, lorsqu’elle sera atteinte, interrompra le programme
d’arrosage. Cette quantité se situe entre 3mm et 25mm (de
pluie). Pour régler, tourner le bouchon jaune et sélectionner la
quantité désirée (voir Fig.5)
4
3
2
1
GB
F
5
4
3
2
1
AC Sensor
AC Sensor
Installation
Installation
Contact Details
Troubleshooting
I
ssue
P
roblem
S
olution
W
atering
paused by
AC Sensor cuts
o
ff too quickly
A
C Sensor is drying
off too quickly
C
hange the position
of the vent ring cap
(See section 5)
W
atering
paused by
AC Sensor
c
omes on
too late
A
C Sensor needs to
be more reactive to
rainfall
C
hange the rainfall
measurement cap to
a lower value
(
See section 4)
Rain doesn’t
trigger the
A
C Sensor to
work
Rain is not falling
directly on the
A
C Sensor
Check that there are
no obstacles over or
a
round the AC Sensor
that might be
preventing the rain
f
rom falling on it.
Re-locate if needed
T
he AC Sensor has
not sensed enough
water to stop
watering
C
hange the rainfall
measurement cap to
a lower value
(See section 4)
Troubleshooting
Issue Problem Solution
Water
computer has
not recognised
the AC Sensor
Water computer
display is in
power-save mode
Press and hold any
key to continue
Check the AC Sensor
is installed correctly
Check cables and plug
for damage. Check the
AC Sensor is connected
correctly
(See Section 2)
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hozelock 2702 AC sensor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hozelock 2702 AC sensor in the language / languages: All languages as an attachment in your email.

The manual is 21,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info