Manual Hozelock 2597 (page 5 of 60) (All languages)

661708

Zoom out

Zoom in

1/60

Contents

Auto Reel

Wall Bracket

Feeder Hose

Threaded Tap Connector

Hose End Connector

Waterstop Connector

Wall Plugs and Screws

Hose Nozzle

Quick hints and tips

• When mounting the reel, ensure that nothing

obstructs the reel from swinging freely through 180°.

• It is critical to use a 7mm drill when drilling holes to

mount the reel.

• Ensure the wall bracket is mounted vertically using a

spirit level.

• Check that the reel is locked onto the bracket before

turning on water supply.

• The hose will not rewind unless it is pulled a short

distance (15 to 30cm) away from the reel and then

walked back towards the reel.

• If the hose will not rewind, try the following;

Turn off the tap and let the water out of the hose by

opening the hose nozzle/gun.

Walk back to the reel with the end of the hose and

trigger the rewind mechanism by taking hold of the

hose near to the reel, and gently pull the hose about

15 to 30cm to release the latch.

(Ensure that nothing is obstructing the hose whilst

the rewind procedure is active.)

• Use the lock on the side of the reel to lock the hose

when not in use.

Assembly and installation

of the Auto Reel

TOOLS NEEDED:

• Flat-ended, long shaft screwdriver

• Philips, long shaft screwdriver

• Pencil

• Tape measure

• 7mm diameter masonry drill bit

• Electric drill/hammer drill

• Spirit level

SELECT A SUITABLE POSITION

FOR INSTALLATION

Fig 1.

• The reel is designed for external use and is not

suitable for use with indoor taps, unless used with

an appropriate Indoor Tap Connector

(Part No’s; 2159, 2176, 2177, 2274, which are not

supplied)

• The reel should be able to swing through 180°.

Allow 65cm of clearance on both sides of the wall

bracket. (See Fig.1)

• If the hose is to be used around corners, the wall

bracket should be mounted at least 1.60m from the

corner, and a hose guide should be used

(part no; 2392, which is not supplied.)

MOUNT THE WALL BRACKET

Fig 2.

• Remove the Wall bracket (Contents B) from the reel

by releasing the locking clasp on the reel (Fig.2a).

The wall bracket can now be removed ready for

mounting.

• Important: Ensure that the wall bracket is vertical

(with the padlock loop (see fig 6. a) pointing down)

using a spirit level, and that the correct size holes

(7mm diameter and 50mm deep) are drilled

(Fig.2b).

• Use the four wall plugs and screws supplied

(Contents G). The plugs and screws supplied are

designed for use on standard brick and concrete

walls. To fix the bracket to any other surface, you

should use screws and plugs appropriate for that

surface.

CONNECT THE FEEDER HOSE

AND FITTINGS

If the feeder hose supplied is too short to reach your

tap, replace it with a good quality 12.5mm (½”) hose.

Fig 3 – Attaching the Feeder Hose:

• Lay the reel on a soft surface with side

uppermost

and remove the side disc using a flat headed

screwdriver (Fig.3a).

• Unscrew the hose nut from the inlet adapter (Fig.3b).

• Push the feeder hose underneath the hose bridge,

put the nut over the hose (Fig.3c).

• Push the end of the hose into the inlet teeth and

tighten the nut (Fig.3d). Ensure that the hose is

pushed all the way into the inlet. Re-fit the side disc

(Fig.3e).

Attach the hose end connector (Contents E) to the

free end of the feeder hose. Attach the water stop

connector (Contents F - Pre fitted for the Flowmax

model) to the watering hose and connect the nozzle/

gun supplied to the water stop connector (Contents

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hozelock 2597 in the language / languages: All languages as an attachment in your email.

The manual is 2,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hozelock 2597 Manual

Product: