Manual Hotpoint FDFEX 11011 EXTRA (page 5 of 20) (English)

670829

Zoom out

Zoom in

1/20

If the appliance must be moved at any time, keep it

in an upright position; if absolutely necessary, it may be

tilted onto its back.

Positioning and levelling

1.Removetheappliancefromallpackagingandcheckthatit

has not been damaged during transportation.

If it has been damaged, contact the retailer and do not proceed

any further with the installation process.

2.Checkthedishwasherbyplacingitsothatitssidesorback

panel are in contact with the adjacent cabinets or even with

the wall. This appliance can also be recessed under a single

worktop*

(see the Assembly instruction sheet).

3. Position the dishwasher on a level and sturdy floor. If the

floor is uneven, the front feet of the appliance may be adjusted

until it reaches a horizontal position. If the appliance is levelled

correctly, it will be more stable and much less likely to move or

cause vibrations and noise while it is operating.

4*. Adjust the height of the rear foot from the front of the

appliance on the central lower part of the dishwasher, turning

a hexagonal spanner (red color) with an opening of 8 mm in a

clockwise direction to increase the height or in an anticlockwise

direction to decrease the height.

The dishwasher meets the requirements set out by the

regulations in force concerning safety and electrical equipment.

Any technical checks should be conducted exclusively by

a trained and authorised technician: Repairs carried out by

unaithorised persons will invalidate the guarantee, as well as

posing a potential hazard to the user.

The manufacturer declines all responsibility for damage to

persons or property resulting from failure to observe the above

precautions, from tampering with even a single component or

from the use of non-original spare parts.

Electrical Connection

Before inserting the plug into the electrical socket, make sure

that:

• thesocketisearthedandcomplieswithcurrentregulations;

• thesocketcanwithstandthemaximumloadoftheappliance,

which is indicated on the data plate located on the inside of

the door

(seeDescriptionoftheappliance);

• thepowersupplyvoltagefallswithinthevaluesindicatedon

the data plate on the inside of the door;

• thesocketiscompatiblewiththeplugoftheappliance.Ifthis

is not the case, ask an authorised technician to replace the

plug

(see After Sales Service)

; do not use extension cables

or multiple sockets.

Oncetheappliancehasbeeninstalled,thepowersupply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order

to prevent all potential hazards.

(See After Sales Service)

This appliance must be earthed.

Fuses:yourappliancecomesfittedwithapluganda13Afuse.If

youneedtoreplacethefuse,onlythoseratedat13AandASTA

approvedtoBS1362shouldbeused.Ifyoulosethefusecover,a

replacement may be obtained from your local authorised Service

CentreorElectricalcompany.Correctreplacementisidentified

by colour coding or the marking on base of plug.

DONOTusetheplugunlessthefusecoverisfitted.

Changing the Plug

Cutoffanddisposeofthesuppliedplugifitdoesnotfityour

socket.

ToavoidashockhazardDONOTinsertthediscarded

plug into a socket anywhere else.

Wiresinthemainsleadarecolouredaccordancewiththe

following code:

Green/Yellow- Earth

Blue  - Neutral

Brown - Live

If you change the plug, the colour of the wires in the mains lead

may not correspond with the terminal markings in the plug, which

if not coloured, could be:

EARTH ‘E’or

NEUTRAL ‘N’

LIVE  ‘L’

Changing the Mains Lead

A lead can be ordered from Hotpoint Service

UK:08709066066or

RepublicofIreland:1850302220

- If you have damaged the existing lead or require a longer one

a charge will be made. It is strongly advised that this work is

carried out by a qualified electrician.

- If the domestic wiring includes a residual current-operated

circuit breaker, ensure that it conforms to the latest regulations.

The dishwasher must not be connected to the electricity supply

while installation is being carried out.

-Thisapplianceshouldonlybeconnectedtoa230/240VAC

source, via a properly installed earthed socket.

-Usethedishwashersolelyinadomesticenvironment.

-DONOTstandorplaceheavyobjectsonthedoorwhenitis

open, this could damage the door or cause the appliance to

tip forward.

Installation

* Onlyavailableinselectedmodels.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint FDFEX 11011 EXTRA in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hotpoint FDFEX 11011 EXTRA Manual

Product: