665330
14
Zoom out
Zoom in
Previous page
1/16
Next page
14
GB
The machine vibrates a lot during
the spin cycle.
The machine is noisy.
The machine wont spin properly.
The machine leaks from the
dispenser.
The machine leaks (other than
dispenser).
The machine is locked and an error code
appears on the display (eg F-01, F-..).
The machine smells.
The machine door cannot be
opened.
Door Seal damaged at the bottom.
The water level is too low when
the machine is washing.
The word ‘DEMO ON’ appears in-
termittently in the display window
and the drum slowly turns.
The machine just ‘beeps’ when a
programme or option is selected
(Child Lock Symbol is lit).
There is too much foam.
After completing the programme, or
before starting a programme, the ma-
chine has turned itself off (no lights).
General.
The feet have not been adjusted, enabling the machine to rock.
New Installation - Either the Transit Bolts including the plastic spacers, or the
Polystyrene Packaging have not been removed when installing the machine.
The machine is trapped between cabinets and/or walls.
The load is in a slight out of balance condition and machine is spinning, but at a lower speed.
There will always be some motor, pump and drum noise during spin.
Out of Balance detected when attempting to go into a spin cycle - If this happens the ma-
chine will continue to try to repeat the distribution of the load required before the machine
will go into higher spin speeds - This will increase the programme time accordingly. This is
a safety feature to prevent damage. Out of Balance can be caused by washing a single
heavy item (eg duvet, quilt, etc). - Try the programme again using a different load.
The dispenser drawer is blocked with detergent and requires cleaning.
The water pressure is too high and requires turning down - turn down the tap
on the water supply pipe slightly and try again.
The machine is tilting forwards - It must be level when in its final position.
The fill hose is loose, check both the cabinet and tap ends.
The fill hose is tight but still leaks, if so replace the rubber washers, or the fill
hose is missing the rubber washer.
The drain hose is not fixed in properly.
Switch off the machine and unplug it, wait for approximately 1 minute and then switch it
back on again If the problem persists contact the Technical Assistance Service.
The machine requires a service wash. Run a 90 degree wash cycle with deter-
gent and no laundry.
The door will not open until the door lock indicator light goes out shortly after
the program has finished.
If there is no power to the machine you need to perform the manual unlocking
procedure (see Precautions & Tips).
The door seal has drainage holes at the bottom - This is normal.
The water level is correct if it can be seen at the bottom of the door.
To exit, switch machine off, then press and hold ‘ON/OFF’ and ‘START/PAUSE’
buttons simultaneously for 3 seconds. Note the machine will need the langua-
ge resetting.
Deactivate the Child Lock feature by pressing and holding in the ‘CHILD
LOCK’ button for 2 seconds.
The detergent is not suitable for machine washing (it should display the text
‘for washing machines’ or ‘hand and machine wash’ or the like).
Too much detergent was used - less detergent is required in soft water.
To comply with new energy saving regulations the machine is fitted with an
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate
the machine, it can then either be switched off or a new programme selected.
Your washing machine contains sensors that monitor progress during the wash
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).
Normally, if your machine successfully completes the cycle, there is unlikely to
be anything wrong!
Remember, you will be charged for a service call for problems caused by incorrect installation, as indicated on pages 2 to 4.
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hotpoint-Ariston WDD 756 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hotpoint-Ariston WDD 756 in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info