Manual Hormann Supramatic 2 (page 42 of 46) (English)

459144

42

Zoom out

Zoom in

Previous page

1/46

Next page

7104.2007 TR10A041-C RE

ENGLISH

8 Error messages and warnings

Note: In the event of an error or warning a number is displayed with a rapidly flashing decimal point.

Display Fault/Error/Warning Possible Cause Remedy

Reversing limits cannot

be set

Partial opening height

cannot be set

Entry not possible

Travel command not

possible

Excess travel stop

System fault

Force limit

Closed circuit

Photocell

Closing edge safety

device

No reference point

Operator not

programmed

The operator is at the Open

end-of-travel position

Obstruction when setting the reversing limit "closing

edge safety device/leading photocell"

Partial opening height too close to the CLOSE

end-of-travel position (≤ 120 mm carriage travel)

Parameter in menu 4 set to 0, and activation of

automatic closing tried (menu 3, parameters 1-9)

Travel command given but operator blocked for

control elements

Belt torn

Operator defective

Internal error

Door moves sluggishly or unevenly

Obstruction in door area

Wicket door is open

Solenoid incorrectly installed (wrong way round)

Self-monitoring unit defective

Photocell not connected

Light path interrupted

Photocell defective

Light path interrupted

Power failure

Operator not programmed

Remove obstruction

Partial opening height must be larger

Activate safety device/s

Release operator for control elements

Replace belt

Replace operator

Restore factory settings (see section 4.6)

and reprogramme operator;

replace, if necessary

Correct door movement

Remove obstruction, reprogramme operator,

if necessary

Close wicket door

Install solenoid correctly (see instructions

for wicket door contact)

Replace wicket door contact

Connect photocell or set parameter in

menu 4 to 0

Adjust photocell

Replace photocell

Check transmitter and receiver,

replace, if necessary or completely replace

closing edge safety device

Move door to Open end-of-travel position

Programme operator

The operator is at the Closed

end-of-travel position

The operator is at the intermediate

position

The operator is partly open

The operator is running

Impulse input (radio code)

1

Avrei necessità di riprogrammare il mio SupraMatic P 2 nennlast 225 N. Submitted on 23-3-2023 at 18:59
Reply Report abuse
Tengo un supramatic E2 y quiero conectar una apertura por WiFi, quisiera saber a que conectores, va el modulo wifi Submitted on 28-9-2022 at 18:37
Reply Report abuse
With my previous house I was able to connect additional mains (LED) internal garage lighting that operated in unison with the lighting on the Supermatic. Am I able to do this with the new Supermatic, and what connections do I need to use. Thanks VM Submitted on 16-2-2022 at 16:29
Reply Report abuse
Hoe kan ik de garagepoort "ontkoppelen" van de ketting van de motorisatie om bij stroomuitval manueel te kunnen bedienen? Submitted on 10-5-2021 at 00:39
Reply Report abuse
Good morning,

We have a Hormann Supramatic E2. Very happy with it. This morning however, it closes fine but only opens about 40 cm. This from main button as remote control. Both have the same result. It will close without problem. We have unplugged it and replugged after a few minutes. The track appears to be clear and clean. There is a 5 in red appearing on main unit but I don't know if this is normal to be honest. Advice will be very welcome.
Mariet Procter Submitted on 7-1-2021 at 11:20
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Hormann Supramatic 2 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hormann Supramatic 2 in the language / languages: English as an attachment in your email.

The manual is 7,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hormann Supramatic 2

Hormann Supramatic 2 Usermanual and installation guide - German - 56 pages

Hormann Supramatic 2 User Manual - Dutch - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info