594384

Hoover SPRINT EVO Manual

5
Zoom out
Zoom in
Previous page
1/70
Next page
3
GB
CLEANER MAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust container.
IMPORTANT: To maintain optimum performance, do not allow the dust to sit higher than the
max level.
1. Release the dust container by sliding the dust container release button towards the front
of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Before emptying the Dust Container, gently tap it against the side of a bin to release any
excess dust from the lter.
3. To empty the Dust Container, hold the Dust Container over a bin with one hand and use
the other hand to press the Dust Container Flap Opening Button to release the dust into
the bin. [15]
4. Close the Dust Container Flap and ret the Dust Container to the cleaner main body.
Cleaning the Washable Filters
The cleaner is tted with a pre-motor and exhaust lter. To maintain optimum cleaning
performance, regularly clean the lters. Remove excess dust from the lters by gently tapping
them against the side of a bin. The lters should be washed after every 5 container empties.
IMPORTANT: All bagless cleaners require regular lter cleaning. Failure to clean your
lters may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
IMPORTANT: Regularly check and maintain the lters by following the lter maintenance
instructions, it is also recommended that you purchase new lters after every 3rd lter
wash. This will maintain your cleaners performance.
To access the pre-motor lter:
1. Empty the Dust Container as described in ‘Emptying the Dust Container’. Then, keeping
the Dust Container Flap open:
2. Remove the pre-motor lter by rotating it clockwise at the bottom of the Dust Container. [16]
3. Separate the protective mesh from the lter. [17] Gently tap both the protective mesh
and the lter against the side of a bin to remove excess dust and wash both of them
under warm water. [18] Do not use hot water or detergents.
4. Remove excess water from the lter and leave it to dry fully before reusing. [21]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep cleaning
on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs removal. [1X]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal. [1Y]
Parquet Nozzle* – For parquet oors and other delicate oors. [1Z]
IMPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
5. Once the lter is fully dry, reassemble the lter pack (protective mesh and lter) and ret
to cleaner.
IMPORTANT: Do not use the product without the pre-motor lter pack tted.
IMPORTANT: Always ensure the lter packs are fully dry before use.
To access the exhaust lter:
1. Unclip the exhaust grid from the rear of the cleaner. [19]
2. Separate the lter from the grid and wash the lter under warm water. [20] Do not use
hot water or detergents.
3. Remove excess water from the lter and leave to dry fully before reusing. [21]
4. Remount the lter into the grid and ret it to the cleaner.
Remember: Do not use hot water or detergents. In the unlikely event of the lters becoming
damaged, t a Genuine Hoover consumable. Do not try and use the product without a lter tted.
Removing a Blockage
1. Check if the Dust Container is full. If so refer to ‘Emptying The Dust Container’.
2. If the Dust Container is empty, but suction is still low;
A. Do the lters need cleaning? If so refer to ‘Cleaning the Washable Filters’.
B. Check if there is any other blockage in the system - Use a rod or a pole to remove any
blockage from the tubes or hose.
C. Check for and clear any blockage in the Nozzle
WARNING - If the cleaner is used for a signicant period of time with a blockage, a thermal cut
out will switch the cleaner o to prevent overheating. The bag check indicator turn green once
the cleaner has switched o to signal that the thermal cut out has been activated. If this should
happen, switch the cleaner o, unplug and correct the fault. It will take about 45 minutes for
the cut out to automatically reset.
USER CHECKLIST
Should you have a problem with the product, complete this simple user checklist before calling
your local Hoover service.
•  Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
•  Is the Bag over-filled? Please refer to ‘Cleaner Maintenance’.
•  Is the filter blocked? Please refer to ‘Cleaner Maintenance’.
•  Is the hose or nozzle blocked? Please refer to ‘Removing a Blockage’.
•  Has the cleaner overheated? If so, it will take approximately 45 minutes to automatically
reset.
*Certain Models Only ** Certain models only, nozzles may vary according to model
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover SPRINT EVO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover SPRINT EVO in the language / languages: All languages as an attachment in your email.

The manual is 1,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info