511119
4
Zoom out
Zoom in
Previous page
1/66
Next page
2
GB
(*Certain Models Only)
USING YOUR CLEANER
Extract power cord and plug it into the power supply. 1. [5] Do not pull the cord beyond the
red marker.
Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster up 2.
and raise or lower the handle to the most comfortable cleaning position. [6]
Carpet & Floor Nozzle. Press the oor type selector on the nozzle 3. [7] to select the ideal
cleaning mode for the oor type.
Hard Floor – Brushes are lowered to protect the oor.
Carpet – Brushes are raised for the deepest clean.
Switch the cleaner on by rotating the On/O Variable Power Control Roller clockwise on the 4.
rear of the cleaner main body. [8]
Adjust the power level by rotating the On/O Variable Power Control Roller to the desired 5.
level. [8]
Switch o at the end of use by rotating the On/O Variable Power Control Roller anti-6.
clockwise to the end. [8] Unplug and gently pull the power cord out of the cleaner and the
cord will begin to automatically retract back into the cleaner. [9]
Parking and Storage - The exible hose and tube can be parked for temporary storage while 7.
in use [10] or in the Nanopack storage position when not in use: Retract the telescopic tube
to its storage length [6]. Remove the nozzle from the end of the telescopic tube [11] and
remove the hose handle from the telescopic tube [12]. Lift the hose latch at the rear of
the cleaner [13] and wrap the exible hose around the product [14]. Park the hose handle
on the product [15]. Assemble the nozzle into the parking slot underneath the product
[16]. Assemble the telescopic tube into the remaining parking slot underneath the product
[17].
CLEANER MAINTENANCE
Replacing The Dust Bag
If the bag check indicator [1C] is red please check and, if necessary, replace the bag.
1. Remove the hose from the cleaner [2].
2. Press the Bag Door Release buttons and remove bag door [18].
3. Pull the bag collar to remove the dust bag [19] and carefully dispose the bag into a bin.
4. Fit a new bag into the cleaner by inserting the bag collar into the bag holder [19].
IMPORTANT: The hose must be removed before removing or replacing the dust bag.
Remember: The bag check indicator may be red if an obstruction has occurred. In this case refer
to ‘Removing A Blockage From the System’.
Cleaning the Filters
To maintain optimum performance of your cleaner, please wash the pre-motor lter and exhaust
lter after each 5 bag changes.
To remove the pre-motor lter:
1. Open the bag door and remove the dust bag from the cleaner (see “Replacing The Dust
Bag”).
2. Press the latch at the top of the pre-motor lter frame to unlock it from the cleaner. Tilt and
remove the lter from the cleaner [20].
To remove the exhaust lter:
1. Unlock the door by rotating the door along arrows indicated [21].
2. Remove the lter pack from the recess [22].
Gently tap and wash the lter packs using hand warm water [23]. Remove excess water from the
lters with a dry cloth and leave to dry fully before re-using. Reassemble lter packs once fully
dry and ret to the cleaner.
Remember: Do not use hot water or detergents. In the unlikely event of the lters becoming
damaged, t a Genuine Hoover consumable. Do not try and use the product without a dust bag
or lter tted.
Cleaning the permanent dust bag (depending on model)
To maintain optimum performance we recommend that you wash the permanent bag after
every 5 full bags. Empty the contents of the Bag into a bin, wash the Bag under handwarm
water, remove excess water with a dry cloth and leave to dry fully before replacing.
Removing a Blockage From The System
If the bag check indicator is red:
1. Check if the bag is full. If so refer to ‘Replacing The Dust Bag’.
2. If it is not full, then;
A Do the lters need cleaning? If so refer to ‘Cleaning the Filter.
B. Check if there is any other blockage in the system - Use a rod or a pole to remove any
blockage from the telescopic tube or exible hose.
C. Check for and clear any blockage in the Nozzle.
Warning - The bag check indicator will turn red if the cleaner is used when full, if there is
a blockage or if the lters are dirty. If the cleaner is used for a signicant period of time
with the bag check indicator is red, a thermal cut out will switch the cleaner o to prevent
overheating. The bag check indicator turn green once the cleaner has switched o to signal
that the thermal cut out has been activated. If this should happen, switch the cleaner o,
unplug and correct the fault. It will take about 45 minutes for the cut out to automatically
reset.
FreespaceEvo__1-4_union.indd 2 16-04-2010 16:24:28
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover Freespace Evo TFV 2011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover Freespace Evo TFV 2011 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info