594446
5
Zoom out
Zoom in
Previous page
1/21
Next page
Water Supply
This machine should only be connected to a cold-water supply. The cold-water
pressure should be between 0.5 and 8 bar (0.05-0.8 Mpa).
Do not connect the machine to a single outlet instantaneous water heater.
Before connecting the fill hose, check that the water is running from the water supply
tap to be used. Let the water flow from the tap until the water runs clear before
connecting to the machine. The water supply tap should be accessible when the
machine is installed.
The water-stop device protects against water damages
caused by leaks on the fill hose which could develop
due to natural ageing of the hose.
In the water-stop system the leaking water fills the
corrugated hose and activates a stop valve which cuts
off the water supply to the machine.
This fault is shown by a red sector on the window "A".
Would this occur, please refer to your Service Agent.
9
Installation
Before installing the machine, ensure that the mains plug and water supply valves are
easily accessible from your chosen machine location.
Make sure there is enough space for the machine. Select a space at least 600mm wide
and 850mm high. Also leave enough space to open the door fully so you can load
and unload it easily.
Keep the area underneath and around the machine free of combustible materials such
as lint, paper, rags, chemicals etc.
All machines are tested with water prior to leaving the factory, so a small amount of
water may be present in the drum and the drain hose.
Flooding may occur if any part of the installation process is not completed correctly.
Electricity Supply
Washing machines are supplied to operate at a voltage of 230-240V, 50 Hz single
phase. Please check that the supply circuit is rated to at least 13A.
The plug is already equipped with a 13A fuse, which is BS 1362 ASTA approved. Any
replacement must be the same rating and specification. If the fuse cover is lost, do not
use the plug until it is replaced.
Electricity can be extremely dangerous. Please take care when connecting your
machine to the electricity supply.
This washing machine must be earthed.
The socket outlet and the plug on the appliance must be of the same type.
Do not use multiple adapters and/or extension leads.
The wires in the mains lead are coloured in accordance with the following codes:
Blue NEUTRAL
Brown LIVE
Green and Yellow EARTH
Appliance complies with European Directive 73/23/EEC, 89/336/EEC
replaced by 2006/95/EC and 2004/108/EC and subsequent amendments.
8
Safety antitwist device
(press and twist to remove
the washer)
A
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover DYN 11146P8CH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover DYN 11146P8CH in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info