Manual Honeywell Y9520Z Sundial RF2 Pack 5 (page 5 of 34) (English)

613689

Zoom out

Zoom in

1/34

A typical use of the EXTRA HOUR button would be if you returned to the house for

a short period when the heating was off. Pressing the appropriate EXTRA HOUR

button gives you 1, 2, or 3 hours of heating, exactly when you need it. Another typical

use is when the heating is already on and you want it to stay on a little longer - just

press EXTRA HOUR and, for that day only, an hour will be added to the end of the

time at which heating normally goes off.

The MODE buttons allow you to select how you want to operate the heating in each

zone independently. The most obvious use is to switch heating OFF during the

summer months, but you may also use this feature if you take a mid-week day off

work, you can then set the MODE to ONCE to keep the system ON during the day

from the ﬁrst programmed ON time till the last programmed OFF time.

The way to use a Room Thermostat

The way to set and use your room thermostat is to ﬁnd the lowest temperature setting

that you are comfortable with, and then leave it alone to do its job. The best way to do

this is to set the room thermostat to a low temperature – say 18°C – and then turn it

up by one degree each day until you are comfortable with the temperature. You won’t

have to adjust the thermostat further. Any adjustment above this setting will waste

energy and cost you more money.

DT92E has a green ECO button, which enables you to set a period of time at a lower

temperature. This energy saving feature is most useful if you are out of the house

for a few hours, or if you want a reduced temperature for a while and don’t want to

have to remember to turn the temperature back up (see pages 22 & 23 for details).

Control of Your Boiler

There are several ways your boiler may be controlled. It may be switched directly

using the ST9520C timer. If installed in a remote location, it may be switched using a

BDR91T relay box. If your boiler supports the OpenTherm communications system,

it may be connected to the ST9520C timer by OpenTherm wiring, over which the

control information is sent.

In each situation the operation of the boiler is determined automatically by the

combination of inputs from the room thermostat and the timer, and in such a way as

to maintain your comfort with minimal energy use. The timer will indicate the on/off

status of the boiler by showing the ﬂame symbol

Optimisation (see page 17 for explanatory diagrams)

Your control system has some features called Optimisation, which aim to save

energy while making you as comfortable as possible. These may or may not be

enabled – check page 34 where your Installer should have indicated how these

were set. Optimisation does not apply to your Hot Water, only to your Heating.

CONTROL OF YOUR SYSTEM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Y9520Z Sundial RF2 Pack 5 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Honeywell Y9520Z Sundial RF2 Pack 5 Manual

Product: