32763
1
Zoom out
Zoom in
Previous page
1/2
Next page
TL8130A
User Guide
Programmable Thermostat
TL8130A 69-1805 3/5/05 1/2
Honeywell’s TL8130A programmable thermostat can be connected to an
electric heater to control the room temperature.
* Set the switch to Standby to cut power to the heater. This will not affect the time
and temperature settings.
** The thermostat displays the heater duty cycle required to maintain the desired tem-
perature. For example, appears when the heater is activated 40 percent of the
time.
To remove the control module from the power
base, loosen the captive screw underneath the
thermostat and pull the two components apart as
shown.
To install the control module onto the power
base, reverse the above procedure.
NOTE: Always keep the thermostat's vents clean and
unobstructed.
Some thermostat configurations can be
modified via the switches on the back of the
control module.
Default (factory) settings are inside the gray cells.
Upon power-up, the thermostat is in manual mode ( ) and displays the
actual temperature.
n Press the Hour and Min buttons to set the time.
o Press the Day button to set the day.
LO: The measured temperature is below 0°C (32°F).
Heating is activated.
HI: The measured temperature is above 50°C (122°F).
When the backlight button is pressed, the display illuminates for 5 seconds.
When either of the buttons is pressed, the display illuminates for 10 sec-
onds.
Setpoint
The thermostat normally displays the actual temperature. To view the set-
point, press one of the buttons once or press the backlight button. The
setpoint will appear for the next 5 seconds.
To change the setpoint, press one of the buttons until the desired temper-
ature is displayed. To scroll faster, hold the button.
Preset buttons
The thermostat has 3 temperature preset buttons:
Comfort preset button
Economy preset button
Vacation preset button
To use a preset temperature, press the appropriate button. The corresponding
icon , or will be displayed.
The following table shows the intended use and the default setting of each of
the preset buttons.
To store a preset temperature:
n Set the desired temperature using the buttons.
o Press and hold the appropriate preset button until the corresponding
icon is displayed.
p Press Mode/Ret to exit.
n
Description
1.
Display
% of duty cycle 1 to 24% 25 to 49% 50 to 74% 75 to 99% 100%
o
Assembly/Disassembly
2.
p
Configuration
3.
# Configurations UP DN
SW1
Temperature format
a
a. If you change the temperature display format, the preset buttons ( , and )
will return to their default settings.
°F
°C
SW2
Early Start
b
b. Early Start can be used in Automatic mode only. When this function is enabled, the
thermostat calculates the optimal time to start heating in order to obtain the desired
temperature by the set time. The thermostat re-assesses the start time daily based
on the previous day’s performance.
Disable Enable
SW3 Time format 12-hour
24-hour
On/Standby
switch *
Day and time
settings
Temperature
adjustment
buttons
Program button
Mode selection /
program exit
Temperature display
Mode display
Period display
Temperature
preset buttons
Time and day display
Heating power **
Backlight button
Program
clear button
Preset temperature
icon
Appears when
the setpoint is
displayed
q
Power-up
4.
r
Error Messages
5.
s
Backlight
6.
t
Temperature Setting
7.
Icon Intended use Default setting New
Comfort
(when at home)
21°C (70°F)
Economy
(when asleep or away from home)
16.5°C (62°F)
Vacation
(during prolonged absence)
10°C (50°F)
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell TL8130A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell TL8130A in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell TL8130A

Honeywell TL8130A User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info