Zoom out
Zoom in
Previous page
1/34
Next page
HONEYWELL
TE831W-2
COMPLETE WIRELESS WEATHER STATION
USER MANUAL
TE831W-2
Downloaded from www.Manualslib.com manuals search engine
1


Need help? Post your question in this forum.

Forumrules


Content of pages


  • Page 1

    HONEYWELL TE831W-2 COMPLETE WIRELESS WEATHER STATION USER MANUAL TE831W-2 Downloaded from www.Manualslib.com manuals search engine ...
  • Page 2

    Table of Contents Introduction Standard Package Contents Installation Before you begin Thermo-Hygrometer Sensors TS33C Rain Gauge TS906 Anemometer (wind sensor) TS805 Main Unit Power Buttons and Controls Initial Set up Connecting the Weather Station to a PC Operation and Window Selection Custom Weather Station Settings LED Backlight Options Time Alarm Settings Memory Reset procedure Maintenance Troubleshooting PRECAUTIONS Appendix - City Codes Specifications FCC STATEMENT DECLARATION OF CONFORMITY STANDARD WARRANTY INFORMATION 3 3 3 4 5 6 8 10 11 12 14 14 15 16 25 25 27 27 28 29 29 30 33 34 34 2 Downloaded from www.Manualslib.com manuals search engine ...
  • Page 3

    Introduction Thank you for selecting the Honeywell Complete Wireless Weather Station. This compact and easy-to-use product uniquely measures and monitors weather data right at your immediate location. It includes a wide range of weather features plus precise atomic time and perpetual calendar. Weather measurements include: air temperature, relative humidity, barometric pressure, wind speed and direction, rainfall levels and more. Standard Package Contents In this package you will find: One Main Unit (receiver) (TE831WD) One Rain Gauge (remote rain sensor/transmitter) (TS906) One Anemometer (remote wind sensor/transmitter) (TS805) Two of each Three-Channel Temperature & Humidity Sensors (transmitter) (TS33C) One 7.5V AC/DC Adapter One CD-ROM disk One 2m (6ft) USB cable Anemometer Mounting Hardware with wrench tool One User Manual Required for installation (not included) - Small Phillips screwdriver - Anemometer mounting pole - Small paper clip to reset sensors NOTE ...
  • Page 4

    Before you begin The components of this Honeywell Complete Wireless Weather Station operate at 433MHz radio frequency. No interconnecting wires are required between the main unit (receiver) and the remote sensors (transmitters). Note: Your weather station comes with alkaline batteries included in each weather instrument. To activate each component remove clear protective plastic strip from the battery compartment in the following order: Anemometer (wind sensor) Rain Gauge (rain sensor) IMPORTANT: The Rain Gauge battery compartment locates inside the funnel assembly – please refer to Rain Gauge setup page in this User Manual. The First of the Thermo-Hygrometers (temperature and humidity sensor) The Second of the Thermo-Hygrometers (temperature and humidity sensor) IMPORTANT: The First of the Thermo-Hygrometer sensors is pre-set for Channel 1 and will start transmitting data on Channel 1 immediately after protective plastic strip is removed. The Second Thermo-Hygrometer senso ...
  • Page 5

    • Make sure that the remote sensors are easily accessible for cleaning and maintenance. Note: When the temperature falls below freezing, the outdoor sensor batteries may have reduced voltage and a reduced effective range. We recommend using lithium batteries at temperatures below 32°F (0°C). IMPORTANT: We recommend cleaning the remote sensors periodically, as dirt and debris affects sensor accuracy. Thermo-Hygrometer Sensors TS33C FEATURES • • • • • LCD display of measured temperature and humidity Remote data transmission to the main unit via 433 MHz signal 328 feet (100 meters) transmission range without interference Three (3) transmission channels selection Case can be wall mounted using built-in hanger A. LED INDICATOR • Flashes once when the remote sensor transmits a reading to the main unit. • Flashes twice when battery power is low. B. BATTERY COMPARTMENT Holds two AA-size batteries C. RESET Resets all readings (requires small paper clip.) D. CHANNEL ...
  • Page 6

    • Set one sensor to Channel 1 and the second sensor to Channel 2, etc. The sensors must operate on separate channels. Install 2 “AA” size batteries matching the polarities shown in the battery compartment. IMPORTANT: When channel number is selected, it will be displayed on the sensor’s LCD display • Replace the battery compartment door and secure the screws. • Secure the thermo-hygrometer remote sensor in the desired location. Mounting • The remote thermo-hygrometer sensor can be placed on the flat surface or mounted on the wall in vertical position • Use the screws when mounting the thermo-hygrometer sensor on the wall Placement tips: • The remote thermo-hygrometer sensor should be placed in the area with a free air circulation and sheltered from the direct sunlight and an extreme weather conditions. • • • • Ideally, place the thermo-hygrometer sensor above the natural surfaces (such as a grassy lawn). Avoid placing the thermo-hygrometer sensor near sour ...
  • Page 7

    G D B A H E C F I D. Funnel-shaped top with battery compartment Contains battery compartment and rainfall counting electronics E. Battery compartment Holds two AA-size batteries F. Screws Secures battery compartment cover G. Built-in level with bubble Ensures level rain gauge mounting for proper operation H. Bucket see-saw mechanism Collects the rainfall in one of its containers and self-empties once full I. Protective screen Protects the rain gauge funnel from debris Battery installation • Unlock the funnel-shaped top on the rain gauge by turning both knobs on the sides in an anti-clockwise direction. • Remove the funnel-shaped top lifting it off the rain gauge bucket. • Remove 7 small screws from the battery compartment cover using a small Phillips screwdriver • Insert 2 “AA” size alkaline batteries (not included), matching the polarities as shown in the battery compartment. • Replace the battery compartment door and secure the screws. • Insert ...
  • Page 8

    • • • Place the protective screen over the top to protect the rain gauge from the debris. Where practical, mount the rain gauge in place with wood screws (not included). Make sure that the rain gauge is in open area where precipitation falls directly into the gauge’s bucket, ideally 2-3 feet above the ground. Placement tips • The rain gauge should be placed in an open area away from the walls, fences, trees and other coverings which may reduce the amount of rain falling into the bucket. Additionally, trees and rooftops may be sources of pollen and debris. • To avoid the rain shadow effects, place the rain gauge horizontally, on the distance corresponding to two to four times the height of any nearby obstruction. • It is important to locate the unit where rain can flow away freely. Anemometer (wind sensor) TS805 FEATURES • • • • Wind speed and wind direction measurement Remote wind speed and wind direction data transmission to the main unit via 433 ...
  • Page 9

    A E D G C B F H E. WIND CUPS SHAFT Holds wind cups on the anemometer arm F. BATTERY COMPARTMENT Holds 2 AA-size batteries G. WALL MOUNT SCREW OPENINGS Allows securing the anemometer in place H. BATTERY COVER Secures battery compartment on the anemometer base Assembly • • Slide the wind cups on to the anemometer rotating shaft. Do not use force. Insert the longer arm of the Allen Wrench (provided) into the wind cup set screw opening. Feel the head of the set screw inside the wind cups and tighten carefully the set screw securing the wind cups to the rotating shaft. • Test to ensure cups are securely fastened to the shaft and cannot be removed Battery installation • • • Remove four (4) screws from the battery compartment with a small Phillips screwdriver. Open the battery compartment and install 2 “AA” size alkaline batteries (not included) matching the polarities shown. Do not close battery compartment yet as you need to make sure that the an ...
  • Page 10

    unit (0.0 mph will appear on the main unit’s wind window if the signal was sent and received successfully) Aligning This procedure must be performed after main unit has been powered and all remote weather sensors were received successfully. • • Manually point the wind direction vane to the north (use a compass or map if necessary). Press the “SET” button located inside battery compartment (on the shorter side) with a paper clip. “SET” button selects a new direction for NORTH and, when pressed repeatedly, alternates between the factory default NORTH and user selected NORTH. • Watch for the next anemometer data transmission in the main unit’s wind window – the direction will be updated • Replace the battery compartment door and secure the screws. Note: Repeat aligning procedure every time after changing the batteries. Mounting Mount the anemometer onto a vertical surface, using the fittings provided. Placement tips: • The anemometer should be mounted in an open are ...
  • Page 11

    • • • • • • • • • • • Barometric pressure in imperial or metric units Altitude adjustment for pressure compensation 24 hour barometric pressure history chart Multiple weather alerts including: Hi/Low temperature, Daily Rainfall, Hi wind gust and Hi wind speed alerts Indoor/Outdoor Temperature & Humidity in up to 5 remote locations (3 additional sensors required) Dew point and comfort level indicators Wind direction, speed and wind gust averages and memory Rainfall amount with minimum and maximum memory 200 weather records without PC connection PC software (included) and USB port Operating range from 100 feet (30 meters) up to 328 feet (100 meters) • Light sensor detects low light conditions and LCD lights up automatically when adapter is connected Display Power • Open the battery compartment door on the back of the main unit. • Insert four (4) AA size batteries according to the polarities shown and replace the battery compartment door. • Connect 7.5V ...
  • Page 12

    Buttons and Controls H I G F E D C B A K L J 12 Downloaded from www.Manualslib.com manuals search engine ...
  • Page 13

    A. UP B. DOWN C. SET D. CHANNEL E. MEMORY F. HISTORY G ALARM/CHART H. SENSOR - Selects the next available window counter-clockwise - Increases parameters -If depressed and held, activates an atomic time signal search - Selects the next available window clockwise - Decreases parameters -If depressed and held, activates all remote sensors signal search - Alternates the parameters for the selected window - If depressed and held, enters into the programming mode or changes parameter’s units - Pressed again closes programming mode and confirms selected parameters - Manually selects the channel # for receiving temperature and humidity sensor data - Enables the temperature and humidity channel auto-scan mode - Records: moon phase, temperature, humidity, rainfall and wind records. Then stores in memory - Moon phase: Determined by the day of month interval - Sets and stores pressure & altitude units in Memory - Allows displaying the sea-level pressure history ...
  • Page 14

    Initial Set up 1. Power up each of the remote sensors as instructed in previous sections.( Remove clear protective plastic slips from the battery compartments) 2. Then power up the main display. 3. Once the main unit is powered, the display will briefly show all available LCD segments for a moment. 4. IMPORTANT: Do not press any buttons during the set up process which typically takes about 5-10 minutes. The display functions will be automatically set including local altitude and pressure parameters. The display will show the pressure icon and “inHg” (inches of Mercury) flashing. You will know that the unit is finished self-adjustment when the display shows the default settings for the pressure and altitude (sea level) Indoor/outdoor temperature and humidity readings, remote sensors readings, etc. Many settings can be changed or customized to your preference, after the display has stabilized • • • The pressure parameters during Initial Setup (See Pressure and Weather Fo ...
  • Page 15

    If you want to use collected weather data in other applications, the software allows storing data on your computer hard drive in text file called RECORDS.txt. This file can be exported to Excel. This file location is: C:/Program Files/WeatherCapture. NOTE: Check our website periodically for useful tips and the latest software versions Operation and Window Selection The main unit has five different operating windows each displaying unique data. When a specific window is selected the corresponding icon will start flashing. Press the UP arrow button on the main unit to cycle through the windows clockwise or DOWN arrow button anti-clockwise. The basic operation of your weather station has been designed to work straight out of the box 10 minutes after power is provided to the main unit. You will have to select a city location following the steps identified under INITIAL SETUP before proceeding. Clock and Alarms Window Clock and Calendar Displays To alternate your view of the ...
  • Page 16

    • With the Clock and Alarm icon flashing, press and hold SET button until the day of week language abbreviation “ENG” will flash. • Press UP or DOWN arrow button to select the desired language for day of the week in English, German, French, Italian, Spanish or Dutch • • Press SET button to confirm selection. Select the desired City Code flashing (LAX is Los Angeles for example) for your area by pressing UP or DOWN. This will set the unit to the appropriate time zone for your location. Refer to table, back of this book, for a list of available cities. • • • • Press SET to confirm the city selection. Press UP or DOWN to select the correct year. Press SET to confirm year selection. Press UP or DOWN to select the correct month. • • • • • • • Press SET to confirm selection. Press UP or DOWN to select the correct date. Press SET to confirm selection. Press UP or DOWN to select the correct order of month & year. (M…D) Press SET to confirm selec ...
  • Page 17

    Pressure and Weather Forecast Window Your weather station is designed to display (local) barometric pressure, sea level pressure, weather forecast and moon phases. Historical statistics can also be viewed, including the sea-level pressure for the past 24 hours, moon phase for the past and following 39 days, and a selectable bar-chart for viewing pressure/ temperature & humidity history. Pressure is displayed inHg (English), hPa/mBar (scientific) or mmHg (metric). Altitude is displayed in meters or feet. Display: Select Pressure and Weather Forecast Window Press UP or DOWN arrow buttons on the main unit until the weather forecast icon begins to flash, upper display left corner. NOTE: Wait at least 5 - 10 minutes after initial set up to view a pressure or altitude information. Pressure and Altitude Information Press SET button once (do not hold it) to alternate between the Sea Level Pressure, Local Pressure and Local Altitude settings. The unit should be set to the ...
  • Page 18

    desired at a later date, using the steps outlined in the section for Setting or Changing Pressure and Altitude settings. Changing Pressure and Altitude Parameters The weather station is designed to measure local pressure and calculate the other two parameters based on the Local Pressure. Sea Level Pressure and Altitude are interdependent. If you adjust altitude, it will calculate sea level pressure, if you adjust sea level pressure, it will automatically calculate altitude. You can only adjust one of the two – either sea level barometric pressure or altitude. If you wish to know pressure changes at your specific location (house), the LOCAL barometric pressure should be selected In this case, the local altitude/elevation must be programmed according to GPS readings, Internet, etc. If you wish to know pressure changes in your surrounding metro area, then SEA LEVEL barometric pressure option should be selected. In this case, the SEA LEVEL barometric pressure value can be adjusted ...
  • Page 19

    • • Press and hold SET until the altitude digits are flashing. Set the altitude value by pressing the UP or DOWN arrow buttons. Press and hold UP or DOWN arrow button for faster digits advancement • Press SET button to confirm your selection. Viewing the Sea Level Pressure History • • From any mode, press the HISTORY button. Unit will select the Pressure/ Weather display. When the SEA LEVEL is displayed, press HISTORY button repeatedly viewing the sea level pressure history for the past 24 hours in hour intervals. • If no buttons are pressed for 5 seconds, the unit will automatically exit history mode and return to the Pressure and Weather Forecast mode . Viewing the Pressure, Temperature and Humidity Bar Charts The pressure bar graph shows barometric pressure variations over the past 24 hours. This is very useful for understanding the Barometric trends that are used in weather forecasting. Each bar icon represents 0.06 inHg. Alternatively, the bar c ...
  • Page 20

    Weather Forecast Displays Note: The weather forecast accuracy is approximately 70%. Display shows 12 to 24 hour forecast, not current conditions. The SUNNY icon indicates clear weather, even when displayed during the night-time. Temperature and Humidity Window The weather station supports Indoor Temperature & Humidity and up to five remote temperature and humidity sensors (2 remotes are included). Temperature can be displayed in either Celsius (ºC) or Fahrenheit (ºF). The main unit calculates indoor comfort level - Wet, Comfort or Dry. Dew Point based on temperature & humidity readings. The main unit can be programmed to alarm if the temperature exceeds or falls below the pre-set upper and lower limits on all remote channels. The limits are the same for all 20 Downloaded from www.Manualslib.com manuals search engine ...
  • Page 21

    remote channels Thermo-Hygrometer remote battery status is monitored on the main unit. Display: Selecting Temperature and Humidity Window Press main unit UP or DOWN arrow buttons until the IN icon on the upper right will flash. Viewing Temperature and Humidity for each Channel At any time simply press the CHANNEL button to recall a different remote thermo hygrometer channel. Channel Auto-Scan Display: To enable automatic scan of all available channels, press and hold CHANNEL button, until the Channels will be alternately displayed with a 5-second delay. icon is displayed. Temperature and Dew Point Displays With Temperature and Humidity icon flashing, press the SET button to alternate between “temperature and relative humidity” or “dew point and relative humidity.” Temperature in Celsius or Fahrenheit With Temperature and Humidity icon flashing, press and hold the SET button to alternate between temperature in Celsius (ºC) or Fahrenheit (ºF). Temperature A ...
  • Page 22

    with icon (if disabled, displays OFF). You can program the same temperature alarm limits for all five temperature and humidity channels Programming Upper and Lower limits for Temperature Alarm • In the Temperature and Humidity Mode, press ALARM/CHART button once selecting the desired alarm limit – Upper or Lower • Press and hold ALARM/CHART button until the remote temperature and starts flashing. • Adjust the temperature digits for the corresponding Temperature Alarm limit using the UP Sor DOWN Tbuttons. Press and hold either button for fast digits advance. • Press the ALARM/CHART button to confirm selection and return to the Temperature Alarm selection screen. (Upper Alarm) or (Lower Alarm) icon Disabling Temperature Alarm levels With the Temperature & Humidity icon flashing, press the UP or DOWN arrow button to disable the alarm(s) – OFF will be displayed if alarm is disabled Note: The temperature alarms have a 0.5 ºC deviation to prevent false ...
  • Page 23

    Viewing Rain Statistics With the rain icon flashing Press either SET or MEMORY button to recall a rain statistics for the past hour, past 24 hours, yesterday, past week or past month. Note: Last Hour rainfall value is displayed as a rate of rain in either “inch/hr” or “mm/hr”. Rainfall Memory Reset With the rain icon flashing, press and hold the MEMORY button to reset all rainfall statistics. Setting Rain Display; inches or mm With the rain icon flashing, press and hold the SET button to toggle rainfall data units between mm and inches. Enabling or Disabling Daily Rainfall Alert • With the rain icon flashing, press the ALARM/CHART button to display either the current rainfall statistics or the daily rainfall alert with “ALARM HI” displayed. • • If the alert is disabled, the “OFF” will be displayed; otherwise the rainfall alert value will be shown. When the rainfall alert is displayed, press the UP or DOWN arrow button to enable or disable it. Setting up Daily Ra ...
  • Page 24

    records the maximum wind speed and gusts collected during the day. Wind speed and gust alerts can be programmed based on pre-configured limits. Wind speed is displayed in km/h, mph, m/s or knots. Selecting Wind Window Press main unit UP or DOWN until the WIND icon on the display starts flashing. Note: The wind speed alert is set at 5 mph default and the wind gust alert is set to 7 mph default to prevent false alerts from small fluctuations. Configuring Wind Display With the wind icon flashing, press the SET button to alternate between “wind chill with direction in bearings”, “wind chill with direction in compass points”, “anemometer temperature & wind direction in compass points” or “anemometer temperature and wind direction in bearings.” Setting Wind Speed in km/h, mph, m/s or knots With the wind icon flashing, press and hold the SET button to set the wind speed units in km/h, mph, m/s or knots. Viewing Wind Statistics With the wind icon flashing, press the MEMORY bu ...
  • Page 25

    If the alert is disabled, “OFF” will be displayed; otherwise the alert value is shown. When a wind alert is displayed, press UP or DOWN arrow button to activate or deactivate it. Wind Alert programming • With the wind icon flashing, press ALARM/CHART button to select the desired alarm. • • • Press and hold ALARM/CHART button until alert and corresponding icon will flash. Set the alert using UP or DOWN arrow button. Press and hold either button for fast digits advance. Press ALARM/CHART button to confirm your selection and return to the wind alert selection screen. Disabling the Wind Alert To disable wind alert when it is displayed after pressing ALARM/CHART button press UP or DOWN arrow button – OFF will be displayed instead of previously set alarm time. LED Backlight Options The main unit backlight can be turned on, off or automatic depending on light conditions. The sensitivity of the backlight sensor can be adjusted to high or low using the switch, located ...
  • Page 26

    • • • Set the alarm minutes using UP or DOWN arrow button. Press and hold either button for quick digit advance. Press ALARM/CHART button to confirm selection. Set a Snooze interval (both alarms share same snooze time duration) using UP or DOWN arrow button. Press and hold either button for quick digit advance. • Press ALARM/CHART button to confirm your selection. After programming is completed, the display will return to the alarm selection screen. Disable/Enable Snooze function To enable a snooze function press LIGHT/SNOOZE button. Note: Alarm will automatically “snooze” if no buttons are pressed after the alarm sounds for 2 minutes. This will occur three times only. Disable alarm(s): Press ALARM/CHART button to disable the alarm (s). Note: For weekday alarm, pressing ALARM/CHART button will only disable the alarm for the current day. The alarm will activate again on the next day, Monday through Friday. Atomic Time Reception The purpose of the atomic clock is ...
  • Page 27

    Remote Sensor Status The wave icon above the current channel display shows the connection status of the corresponding remote sensor: Activate Search for Remote Sensors Normally the main display will automatically find and display measurement results from the remote sensors. However, occasionally other radio transmission sources (TV, Cordless or Cell Phones etc) can interrupt the sensor signal. If this happens simply press and hold the DOWN arrow button for 4 – 6 seconds to activate a new search. Memory Reset Procedure These steps will completely reset all of the parameters stored in memory. • On the main unit press and hold SNOOZE and UP buttons for 4 seconds until the backlight will flash • • • Press SET button clearing the memory -the main unit will start beeping with 1 second delay. Wait until the beeping will cease Disconnect main unit from the AC/DC adapter and remove the batteries from the back of the main display unit and wait 10 seconds • Reinsta ...
  • Page 28

    Changing Batteries in the Main Unit • • • First connect the AC/DC adaptor provided to the main unit to avoid losing any data. Remove the battery compartment door at the back and replace all batteries. Do not mix old and new batteries. Replace the battery compartment door. Changing Remote Sensor Batteries • • • Replace the batteries following the setup instructions for the corresponding sensor. When the batteries are properly installed, the remote sensor will resume sending signals to the main unit. To enforce an immediate remote signals search, press and hold DOWN arrow button for 4-5 seconds on the main unit. Cleaning The main unit and remote sensor casings can be cleaned with a damp cloth. Small parts can be cleaned with a cotton tip or pipe-cleaner. Never use abrasive cleaning agents and solvents. Do not immerse units with electronic parts under water. Anemometer Assure that wind vane and wind cups spin freely and are free from dirt, debris and spider webs ...
  • Page 29

    Check or replace the batteries for the corresponding sensor. Then press and hold DOWN arrow button on the main unit to search for all remote signals. If this does not work, check the wireless transmission path from the corresponding sensor to the main unit and change locations to improve reception. Wireless signals pass through solid objects and walls, however, whenever is possible the sensor should be within line-of-sight with the main unit. The following may cause reception problems: • • The remote weather sensor and a main unit are too far from each other. The signal shielding materials, such as metal surfaces, concrete walls or dense vegetation, are in the path of transmission. • Interference from wireless devices such as: cordless phones, radio headsets and baby listening devices or electronic appliances. Q: “My weather station readings are different from TV, radio or official weather reports.” A: The weather data may vary considerably due to different environm ...
  • Page 30

    Appendix - City Codes The Table below will assist in determining the appropriate time zones. 30 Downloaded from www.Manualslib.com manuals search engine ...
  • Page 31

    Specifications Radio Frequency: 433 MHz RF Reception range: 100-328 feet (30 -100 m) Barometric Pressure Measuring Range: 14.75 inHg to 32.44 inHg (500 Hpa to 1100Hpa); (374.5 mmHg to 823.8 mmHg) Resolution: 0.003 inHg (0.1 Hpa, 0.08 mmHg) Accuracy: 0.015 inHg (5 Hpa; 0.38 mmHg) Sampling interval: 20 minutes Sea level Altitude Compensation Range: -657 ft to 16404 ft (-200m to +5000 m) Temperature (Indoor) Operating Range: 14.2°F to 140°F (-9.9°C to 60°C) Resolution: 0.2°F (0.1°C) Accuracy: 2°F (1°C) Sampling Interval: 10 seconds Temperature (Remote) Range: -40°F to 176°F (-40°C to 80°C) Resolution: 0.2°F (0.1°C) Accuracy: 2°F (1°C) Transmitting Interval: around 47 seconds Operating range: 328 feet (100 m) Humidity (Indoor) Operating Range: 30% to 80% Resolution: 1% Accuracy: 5% Sampling Interval: 10 seconds Humidity (Remote) Operating Range: 30% to 80% Resolution: 1% Accuracy: 5% Sampling Interval: 10 seconds Transmitting Interval: around 47 seconds Ope ...
  • Page 32

    Range: 0° to 360° Resolution: 22.5° Accuracy: 11.25° Starting Threshold: 3mph (4.8 Km/h) Transmitting interval: 33 seconds Operating Range: 100 feet (30 m) Wind Speed Range: 0 to 199.9mph (199.9 Km/h, 173.7 Knots, 89.3 m/s) Resolution: 0.1mph (0.16 Km/h) Accuracy: (2mph + 5%) Starting Threshold: 3mph (4.8 Km/h) Wind/Gust Speed Display Update Interval: 33 seconds Wind/Gust Sampling Interval: 11 seconds Operating Range: 100 feet (30 m) Rainfall 1h/24h/yesterday range: 0 to 78.73 inch (0 to 1999.9 mm) Last week/ last month range: 0 to 787.3 inch (0 to 19999 mm) Resolution: 0.03 inch (0.6578 mm) Accuracy: +/- 5% +/- 0.03 inch (+/-5%mm +/-0.6875) Transmitting Interval: 183 seconds Operating Range: 100 feet (30 m) Hardware Requirement for WeatherCapture PC software Operating System: Windows 98/NT/2000/ME, XP or Vista Memory size: Ram 128 MB or more Hard disk size: 100 MB free space or more Media Device: 1 x CD-Rom drive Available serial USB port Power (12 AA Batter ...
  • Page 33

    Battery life (alkaline) Main unit: 2 month (without AC adapter) Thermo-Hygrometer: over 12 months Anemometer: 2 years Rain Gauge: 2 years Weight (without batteries) Main unit: 8.15oz (231g) Remote Thermo-Hygrometer: 2.29oz (65g) Remote Anemometer: 11.12oz (315g) Remote Rain gauge: 10.24oz (290g) Dimensions Main unit: 7.31 (L) x 5.39 (H) x 1.26 (D) inches / 185.8 (L) x 136.9 (H) x 32 (D) mm Remote Thermo - Hygrometer: 2.37 (L) x 4 (H) x 1 (D) inches / 60 (L) x 101 (H) x 25 (D) mm Remote Anemometer: 19.16 (L) x 19.16 (H) x 15.35 (D) inches / 486.6 (L) x 486.6 (H) x 390 (D) mm Remote Rain gauge: 6.49 (L) x 6.89 (H) x 4.72 (D) inches / 165 (L) x 175 (H) x 119 (D) mm FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes o ...
  • Page 34

    DECLARATION OF CONFORMITY Name: Hideki Electronics, Inc. Address: 7865 SW Mohawk, Tualatin, OR 97062 Telephone No.: 1-503-612-8395 declare that the product Product No.: TE831W-2 Product Name: Complete Wireless Weather Station Manufacturer: Hideki Electronics Ltd. Address: Unit 2304-06, 23/F Riley House, 88 Lei Muk Road, Kwai Chung, New Territories, Hong Kong is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. The information above is not to be used as a contact for support or sales. Please call our customer service (refer to the Standard Warranty Information) for all injuries instead. STANDARD WARRANTY INFORMATION This product is warranted from manufacturing defects for one year from the date of retail purchase. It does not cover damages or wear resulting from acc ...



Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell TE831W-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell TE831W-2 in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info