613685
14
Zoom out
Zoom in
Previous page
1/18
Next page
14
FAQ AND TROUBLESHOOTING
How do I set the time only, if the ST9500C clock is not
correct?
Your ST9500C contains a very accurate digital clock that is factory pre-set. Should
you ever need to change the time, just follow this procedure:
a. Move the slider to the DAY/TIME position.
b. Keep pressing the green button until the message ‘SET THE TIME’ is
displayed. To change the time, press the or buttons until the correct
time is shown. The message ‘IS TIME OK?’ will be displayed. Press the green
button to confirm the time is correct. If you have made a change, the message
‘TIME SAVED’ will show, followed quickly by ‘DATE + TIME COMPLETE’.
c. Move the slider to the RUN position, to complete changing the time.
What do I do when the clocks go back in October and forward
in March?
Your ST9500C is factory-set to adjust the clock automatically at the correct dates,
so you should never need to adjust the clock forward or backwards yourself. It is
possible to disable this particular feature, as described in the section ‘Changing the
Installer Parameters’ (page 12). You may also check the section ‘Configuration &
Service Data’ (page 18) to see how your Installer has configured your product.
What should I do if I get ‘lost’ while programming the
ST9500C?
The LoT™ Display on ST9500C will provide you with help and tips to work through
the programming. Should you ever get ‘lost’, the simplest thing to do is to move the
slider to the RUN position, and then move it back to the appropriate programming
position where you got lost. At this point just follow the instructions again.
What happens if there is a power failure?
In the event of a mains power failure, the ST9500C display will go blank, the
indicator lamps will go out, and the control outputs will switch off. The real time will
be constantly maintained by means of the built-in battery backup, ready to power
back up as if nothing had happened when the mains power is restored. In addition,
all programmes and settings are stored in a special memory (called NV memory)
which requires no power to maintain information, and so will be retained indefinitely.
Should the correct time and date ever be lost, for whatever reason, the message ‘SET
DATE + TIME’ will be displayed whilst the slider is in the RUN position. In this case,
simply follow the procedure described under Step 1: Setting the Date & Time
(page 4). It should not be necessary to make any changes to your programmes.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell ST9500C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell ST9500C in the language / languages: English as an attachment in your email.

The manual is 1,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell ST9500C

Honeywell ST9500C Quick start guide - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info