Manual Honeywell RTH110B (page 3 of 3) (English)

32475

Zoom out

Zoom in

1/3

RTH110B 69-1799 2/6/05 3/3

3.2 Fan Operating Mode

Use the selector switch to set the fan to automatic

mode (AUTO) or continuous mode (ON).

Note: This switch is not used if you have a 2-wire

installation as the fan is not connected to the thermo-

stat.

3.3 Displaying the Temperature

The actual temperature is normally displayed. To view the setpoint,

press once on either of the buttons. The setpoint is displayed

for 5 seconds along with the icon.

Note: Pressing any of the buttons more than once will change

the setpoint.

3.4 Setting the Temperature

Press one of the buttons until the desired temperature is dis-

played.

3.5 Battery Replacement Indicator

An icon appears when the batteries need replacement.

This icon will flash for 120 days, then the thermostat

will cut power to the heating/cooling unit. The icon dis-

appears once the batteries are replaced. The tempera-

ture settings are saved and do not need to be re-entered.

Warning: Before removing the batteries, place the

system switch on the thermostat to Off. Otherwise, the

heating/cooling unit might still be running even after

the batteries are removed.

n To access the configuration menu, press both buttons

simultaneously for 3 seconds.

o To go to the next parameter (menu item), briefly press both

buttons simultaneously.

p To modify a parameter, press one of the buttons.

q Repeat steps 2 and 3 if necessary.

r Press both buttons simultaneously for 3 seconds to exit

the configuration menu.

Power supply: 2 AA batteries

Maximum load: 1 A @ 24 Vac per output

Setpoint range (heating): 41 to 82°F (5 to 28°C)

Setpoint range (cooling): 59 to 95°F (15 to 35°C)

Display range: 23 to 122°F (-5 to 50°C)

Storage temperature: -2 to 122°F (-20 to 50°C)

Temperature display resolution: 1°F (0.5°C)

Accuracy: ± 1°F (0.5°C)

Heating/cooling cycle lengths: 10, 12, 15, 20 or 30 minutes (pro-

grammable)

Compressor short-cycle protection (minimum off time): 5 minutes

Data memory: non-volatile

Dimensions: 5 in. x 3 in. x 1 in. (127 mm x 75 mm x 28 mm)

Honeywell warrants this product, excluding battery, to be free from

defects in the workmanship or materials, under normal use and service,

for a period of one (1) year from the date of purchase by the consumer.

If at any time during the warranty period the product is determined to be

defective or malfunctions, Honeywell shall repair or replace it (at Honey-

well's option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the

place from which you purchased it, or

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care

will make the determination whether the product should be

returned to the following address: Honeywell Return Goods, Dock

4 MN10-3860, 1885 Douglas Dr N, Golden Valley, MN 55422, or

whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This war-

ranty shall not apply if it is shown by Honeywell that the defect or mal-

function was caused by damage which occurred while the product was

in the possession of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product

within the terms stated above. HONEYWELL SHALL NOT BE LIABLE

FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCI-

DENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY

OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,

EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PROD-

UCT. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEY-

WELL MAKES ON THIS PRODUCT. THE DURATION OF ANY

IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS

HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WAR-

RANTY. Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other

rights which vary from state to state.

If you have any questions concerning this warranty, please write Honey-

well Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or

call 1-800-468-1502. In Canada, write Retail Products ON15-02H, Hon-

eywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough,

Ontario M1V4Z9.

If you have any questions about the operation of your thermostat,

please go to www.honeywell.com/yourhome, or call Honeywell

Customer Care toll-free at 1-800-468-1502.

AUTO

• If you have an electric furnace (see section 2.4), the fan works only

when heating or cooling is activated.

• If you have a gas or fuel oil furnace (see section 2.4), the fan works as

follows:

• When the thermostat is placed in cool mode, the fan works only

when cooling is activated.

• When the thermostat is placed in heat mode, the fan is con-

trolled by the furnace fan control circuitry.

ON The fan is always on.

4. Configuration Menu

DISPLAY DESCRIPTION DEFAULT SETTINGS

Temperature display °F °C or °F

Heating cycles per hour

2, 3, 4, 5 or 6

Cooling cycles per hour

2, 3, 4, 5 or 6

When either the heating or cooling parameter is displayed, use the system mode

selector switch to alternate between the two parameters.

For optimal heating control, use the setting that matches your system as follows:

2=30 min (steam or gravity), 3=20 min (hot water or 90%+ high-efficiency furnace),

4=15 min (gas or oil), 5=12 min (alternate setting for gas or oil), 6=10 min (electric).

The corresponding cooling cycle lengths are as follows: 2=30 min, 3=20 min,

4=15 min, 5=12 min, 6=10 min.

5. Technical Specifications

6. Warranty

7. Customer Assistance

Printed in China

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell RTH110B in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell RTH110B

Honeywell RTH110B User Manual - French - 3 pages

Honeywell RTH110B User Manual - Spanish - 3 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Honeywell RTH110B Manual

Product: