723853

Honeywell HT350 Series Manual

2
Zoom out
Zoom in
Previous page
1/11
Next page
2 3
15. Do not operate if the fan housing is
damaged.
16. A loose fit between the AC outlet (recep-
tacle) and plug may cause overheating
and a distortion of the plug. Contact a
qualified electrician to replace loose or
worn outlet.
17. Do not operate any fan with a damaged
cord or plug. Discard any damaged fan,
return the fan to the retailer where the
fan was purchased, or request a return
USER SERVICING INSTRUCTIONS
• Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
• If your fan loses power and you suspect that the fuse on your fan
has blown, you should first remove the spare fuse holder attached
to the cord plug (Fig. 1). Remove the spare fuse from the plastic
spare fuse holder, and set the spare fuse aside (Fig. 2).
• You can gain access to the blown fuse by sliding open the door
found on the side of the plug. Slide the door outward until the
blown fuse is fully visible (Fig. 3).
• Carefully remove the blown fuse and snap the replacement fuse
into place. Risk of fire. Replace fuse only with 2.5 Amp, 125 volt
fuse (provided with product). Fully close the fuse door by sliding
back into place. Discard the blown fuse. The plug should now be
ready for normal use.
• Risk of fire. Do not replace attached plug. Contains a safety device
(fuse) that should not be removed. Discard product if the attached
plug is damaged.
• If you need further information on how or when to replace the
fuse in the safety plug, please contact Kaz Consumer Relations
Department by visiting our website at www.kaz.com or calling
1-800-477-0457.
Thank you for your purchase.
This fan features a fused safety plug which is designed to cut off electric current to the fan if an
electrical fault occurs. Please see below for more information on how to properly use your fan and
replace the safety plug fuse, if needed.
FUSED SAFETY PLUG - FOR US ONLY
Fig. 1
Fig. 2
Fig. 3
FAN OPERATIONFAN OPERATION
HT350 SERIES FAN OPERATION
On/Off
To turn fan on, press the Power button ( ) located on the left side of the control panel.
Sound Level/Speed Control
The fan will automatically start on the“Sleep” level when initially turned on. To adjust the speed
up or down, press the Fan button ( ) repeatedly to increase level.
Oscillation
To activate the Oscillation feature, press the Oscillation button ( ) once. Press the Oscillation
button again to turn the Oscillation off.
authorization to return to Kaz USA, Inc.
for examination and/or repair.
18. Do not run fan cord under carpeting. Do
not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange
cord away from traffic areas and where it
will not be tripped over.
WARNING: To Reduce The Risk of Fire or
Electric Shock, Do Not Use This Fan With
Any Solid-State Speed Control Device,
other than the one supplied.
Model HT350
On/Off
To turn fan on, press the Power button ( ) located on the left side of the control panel.
Speed Control
The fan will automatically start on “Sleep” speed when initially turned on. To adjust the speed up
or down, press the Fan Speed button ( ) repeatedly to increase level.
HT450 SERIES FAN OPERATION
Model HT450
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell HT350 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell HT350 Series in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info