723814

Honeywell HPA030 Manual

4
Zoom out
Zoom in
Previous page
1/24
Next page
4
This model air purifier has an electronic filter check to remind you
when to check and replace the True HEPA filters and pre-filter
based on the air purifier’s hours of use. A red LED will illuminate
when it is time to check/replace the filters.
When the True HEPA filters or pre-filter need to be replaced,
the light will remain on until it is RESET. You may unplug the air
purifier without interrupting the filter check.
You should periodically check the filters. Depending on operating
conditions, the True HEPA filters should be replaced every
12 months and pre-filter every 3 months.
REPLACE WITH TRUE HEPA FILTER and ODOR
REDUCING PREFILTER
R
AA
R
These cleaning intervals are intended as guidelines only.
Performance of any filter media is dependent upon the
concentration of contaminants going through the system. High concentrations of contaminants such as dust, pet
dander and smoke will reduce the useful performance of the filter.
NOTE: None of the filters are washable. DO NOT immerse them in water.
To RESET the Electronic Filter Check:
When the Check Filter LED remains on and solid, it is time to replace the Odor Reducing Pre-filter and reset the
filter monitor. With the unit powered ON, press the FILTER RESET button below the Check Filter LED and hold for
approximately 2 seconds until the light turns off (Fig. 4).
When the LED illuminates and is flashing, it is time to replace the True HEPA filters and reset the filter monitor.
With the unit powered ON, press FILTER RESET button and hold for approximately 2 seconds
until the light turns OFF (Fig. 4).
Manual (or Early) Reset of Electronic Filter Check
Depending on your individual usage (environment and hours used), you may need to replace the filters more or
less frequently. Each time you replace your filters, you should reset the filter monitor. You may manually reset the
filter monitor for the pre-filter or the HEPA filter, or both. If you change the pre-filter or True HEPA filter before the
Check Filter LED is illuminated, it is possible to reset the filter monitor. You must first manually illuminate the
Check Filter LED. Follow these steps:
1. With unit powered ON, press the FILTER RESET button for 5 seconds to illuminate the LED in “solid” mode.
2. To reset filter monitor for pre-filter: press and hold FILTER RESET button for 2 seconds until LED changes to
flashing mode.
3. TAP FILTER RESET button to shut LED off. The pre-filter monitor is now set to “clean status”.
4. To reset filter monitor for HEPA filter: LED must be in “flashing mode”. Follow Step 1 above, then TAP FILTER
RESET button again to illuminate the LED in “flashing mode”.
5. Press and hold FILTER RESET button for 2 seconds until LED shuts off. The HEPA filter monitor is now set to
“clean status”.
6. To reset filter monitor for both pre-filter and HEPA filter: Follow Steps 1,2, and 5 above.
ELECTRONIC FILTER CHECK REMINDER
Will illuminate when it is time to replace the
True HEPA Filters or Odor Reducing Pre-filter
Fig. 4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell HPA030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell HPA030 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 5,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info