OF THIS INSTRUCTION MANUAL BEFORE USING THE EZSENSE
Introduction
ezsense is a small, lightweight, economical gas leak detector
using a catalytic bead sensor requiring no calibration. It can
be used in checking gas leaks in pipes, fittings, valves, gas
storage tanks, home appliances and hot water heaters. It will
detect natural gas, methane, propane, butane and LPG.
1. Unscrew the battery cover, insert 2 x AA alkaline batteries
(Positive terminals in first marked +), replace the battery cover.
2. Slide power switch to ON position. The ezsense will give an
audible alarm and all three LEDs will flash. Wait for twenty
seconds, the buzzer will beep for the end of warm up. Then
the green LED will flash and the confidence beep will continue
to be heard every three seconds. The ezsense is now ready
to use.
3. Check the area suspected of leakage by pointing the gas
sensor close to the area. The audible alarm will sound and
the yellow LED, then the red LED will light up according to
gas concentration if gas is detected.
4. Turn instrument off when finished.
5. The battery needs replacing when the green LED no longer lights.
Operating Instruction
In a well ventilated area, release a small amount of gas from a
butane lighter in front of the sensor. The audible alarm should
sound and the yellow LED and/or red LED will light up.
ezsense Quick Test
Activation of your ezsense's audible buzzer alarm indicates the
presence of combustible gases.
Dispose of instrument and batteries in accordance with local
regulations.
WARNING
Water will damage the instrument.
Avoid using in areas with high humidity. If the ezsense is
not to be used for several weeks, the batteries should be
removed to prevent damage from leakage.
CAUTION
Operation Manual
Honeywell Analytics Distribution, Inc.
400 Sawgrass Corporate Pkwy
Suite 100
Sunrise, FL 33325, USA
Tel: +1 954 514 2700
Toll free: +1 800 538 0363
Fax: +1 954 514 2784
www.honeywellanalytics.com
Flammable Gas Detector
Flammable Gas Detector
Specification
FunctionDetecting flammable gas leakage
Range0 ~ 10,000ppm (20%LEL)*
Green LED: Power On - gas less than 500ppm*
DisplayYellow LED: Low Alarm - over 500ppm*
Red LED: High Alarm - over 2,000ppm*
Approval codes marked, EMC Directive 89/336/EEC
PowerDC 600mW Battery1.5V x 2
ConsumptionSize(AA Alkaline)
DetectableNatural Gas, Temperature-10°~ +50°C
GasButane, Propane,
LPG and LNG
HumidityMax 95%RH CalibrationNot possible
Weight110g Dimension188mm,
Ø30mm
* methane
Honeywell Analytics
4 Stinsford Road
Nuffield Industrial Estate
Poole, Dorset BH17 0RZ, UK
Tel: +44 (0)1202 645577
Fax: +44 (0)1202 665331
In no event will Honeywell be liable for any incidental damages,
consequential damages, special damages, punitive damages,
statutory damages, indirect damages, loss of profits, loss of
revenues, or loss of use, even if informed of the possibility
of such damages. Honeywell's liability for any claims arising
out of or related to this product will in no case exceed the
order value. To the extent permitted by applicable law, these
limitations and exclusions will apply regardless of whether
liability arises from breach of contract, warranty, tort (including
but not limited to negligence), by operation of law, or otherwise.
LIABILITY
3 months from date of purchase, excluding batteries.
WARRANTY
2col1colmonowhite
2col1colmonowhite
MAN0844
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Honeywell GDP11 - ezsense at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Honeywell GDP11 - ezsense in the language / languages: English as an attachment in your email.
The manual is 0.16 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
