723857
3
Zoom out
Zoom in
Previous page
1/14
Next page
4 5
HYF013 SERIES OPERATION INSTRUCTIONS
Place the fan on a level and dry surface.
Plug the power cord into a polarized 120 Volt AC wall outlet.
To operate, turn knob and select appropriate fan speed:
High ( ) Medium ( ), or Low ( ) (Fig. 13).
To activate or disengage the fan oscillation, press the oscillation
button. (
) (Fig. 14).
Operate the automatic shut-off timer feature by turning the timer
knob to the desired setting of 10 to 120 minutes (Fig. 15).
To turn on the fan after automatic shut-off, turn the knob
counterclockwise
to the ON position
.
To turn the fan Off, turn
knob to the Off position.
( )
HYF023 SERIES OPERATION INSTRUCTIONS
Place the fan on a level and dry surface.
Plug the power cord into a polarized 120 Volt AC wall outlet.
To turn the fan on, press the Power button (
) located on
the left side of the control panel.
To select fan speed, press Speed Control button (
) until
the desired speed is selected:
High (
), Medium ( ), or Low ( ) (Fig. 16).
To activate or disengage the fan oscillation, press the
oscillation button (
). Press the Oscillation button again to
turn the Oscillation feature off (Fig. 17).
Fig. 16
Fig. 17
NOTE: Remove all contents from the box being careful not to discard the manual and hardware needed
for assembly. A phillips head screw driver (
) is required for assembly and is not included with the
fan purchase.
A. Pedestal Assembly
Place the power cord through the center of the front and rear
pedestal assemblies with the screw hole openings facing
towards the fan.
Align the front and rear pedestal assembly and firmly snap
together (Fig. 7).
B. Securing the Tower Fan to the Pedestal
Gently turn fan upside down.
Line up the 3 screw holes on the pedestal with the 3 screw
holes on the bottom of the fan housing. Use the 3 (M5 x 12)
screws included in the box and a phillips head screw driver
(
) to secure the pedestal to the fan housing (Fig. 8).
C. Base Assembly
With the fan in the upside down position, pass the power cord
through the recessed slot located in the center of the rear base
assembly (Fig. 9).
Align the rear and front base assembly and firmly snap together
by pushing the 4 round extrusion into the adjacent circles of the
connecting pieces (Fig. 10).
D. Securing the Tower
Fan to the Base
Align the 3 screw holes in
the bottom of the pedestal
with the 3 screw holes
located on the base. Using
the 3 (M5 x 12) screws and
phillips head screw driver
(
), secure the base into
the bottom portion of the
fan housing (Fig. 11).
Place the power cord
through the cut out on the
bottom of the base. Gently
pull any slack out of the
power cord and place the
cord securely in the power
cord holding bracket
(Fig. 12).
Place the fan right side up.
Your fan is now ready for use.
HYF013, HYF023 SERIES ASSEMBLY INSTRUCTIONS
Fig. 10
Fig. 11 Fig. 12
Fig. 9
Fig. 7
Fig. 8
Fig. 14
Fig. 15
Fig. 13
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell DYF012 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell DYF012 Series in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info