32341
13
Zoom out
Zoom in
Previous page
1/14
Next page
Troubleshooting Guide
IF...
Display will not come on.
Temperature display will not go lower
than 45° F
r“
C] or higher than 88° F
[31
0
C]
during programming.
Temperature change occurs at the
wrong times.
Heating will not come on.
THEN...
Set the system switch to
OFF. Remove batteries.
Insert batteries backward for
at least five seconds to
reset thermostat. Replace batteries correctly. Display
should come on.
Make sure batteries are fresh and installed correctly.
Gently clean battery contacts using a soft pencil
eraser. Do not use anything abrasive on clips.
You have reached the temperature setting limit.
The setting range is 45° F to 88°F [7°Cto310 C].
Check the program times for the period in
question. Be sure that AM and PM indications
are correct. Make sure the current day and time are
correct. Reprogram if necessary.
Check that switch on thermostat is set to HEAT.
29
Heating will not come on (continued).
9
Cooling will not come on.
The house is too warm or too cool.
SYSTEM ON indicator is lit, but no
heat is coming from the registers.
:
I
I
(
(
Check the system fuse or circuit breaker and replace
or reset if necessary.
Check for correct wiring and good connections.
Jumper wires R and W. If heat does not come on,
contact your heating dealer.
If display is blank or says “bAt Lo,” install fresh
batteries.
If temperature setting is higher than current tempera-
ture, and SYSTEM ON indicator is lit, contact
Honeywell Customer Assistance at 1-800-468-1502.
Check that switch on thermostat is set to COOL.
Check the system fuse or circuit breaker and replace
or reset if necessary.
Check for correct wiring and good connections.
Jumper wires
Rc
and Y. If cooling does not come on,
contact your cooling dealer.
If display is blank or says “bAt Lo,” install fresh
batteries.
The thermostat has a built-in time delay on cooling.
Allow five to ten minutes after changing the setting
before the air conditioner starts.
30
Make sure outdoor disconnect is engaged (on).
If temperature setting is lower than current tempera-
ture, and SYSTEM ON indicator is lit, move system
switch from COOL to OFF for ten minutes. After ten
minutes, return switch to COOL position. If air
conditioner comes on, compressor may have reached
its high limit temperature protection and shut down. If
air conditioner does not come on after the ten minutes
and the SYSTEM ON indicator is lit, contact Honey-
well Consumer Assistance at 1-800-468-1502.
If 2- or 4-wire installation,
verify that R-Rc jumper is
installed.
Press RUN PROGRAM key to check the current
temperature setting.
f desired, change the temperature setting. See
)age
14.
Wow
time for the furnace to heat up and the fan to
:ome
on before checking for heat at the register.
Check
to make sure system on-time is set
:orrectly
according to pages 16 and 17.)
31
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell CT2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell CT2400 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell CT2400

Honeywell CT2400 User Manual - French - 40 pages

Honeywell CT2400 User Manual - Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info