13039
6
Zoom out
Zoom in
Previous page
1/7
Next page
First
20
Hrs.
operating Every
50
Hrs. operating
CHANGE ENGINE OIL AND REDUCTION GEAR OIL CLEAN AIR CLEANER ELEMENT ing in a dusty area.
Clean more frequently if operat-
ing solvent. After drying, soak in
oil and squeeze out the excess. After hand tightening oil filler cap, tighten
with
a
lever
*
Wash
“B”
and
“C”
in cleaning
solvent. After drying, refill with
clean engine
oil
up
to
oil level
mark.
*
Tap
“D”
and “E” lightly or blow
clean by applying compressed air
from the inside of the elements.
~-
,
Every
100
Hrs.
operating
I
WARNING
CHANGE ENGINE OIL CLEAN FUEL STRAINER CLEAN SPARKPLUG ANDCHECK
GAP
,
Do not use gasoline or
low
flash
,
point solvents for cleaning. They are
ilammable and explosive under cer-
0.6
-
0.7
mrn
(.024
-
,027
in) tain conditions.
Use NGK
B4H
or BR4HS
wash
removed parts
m solvent, dry them
thoroughly and in-
stall securely. Turn
the fuel valve “ON”
and check for leaks.
CDI
rype
Every
300
Hrs.
operating
0.9
-
1.0 mm
LO35
-
,039 in)
Use NGK BPJHS-IO or
BPR-4HS-iO
,
*
Check fuel tube for cracks or
leaks. Replace, if necessary.
1
encine dealer.
The following adjustments should be performed by your Honda general purpose
ADJUST IGNITION TIMING
ADJUST VALVE CLEARANCE ADJUST CARBURETOR SCREWS
*
Carburetor with pilot screw
Adjust contact breaker points
so
that they
*
Measure at TDC on comprcsslon stroke
*
Start the englne and adjust idle speed by
’)
Tighten
the
“IeW
it
just start
to
open, when
“F”
mark on whenengine is cold. turning the throttle
stop
screw.
flywheel aligns with the mark on crankcase.
*
STANDARD:
tightly, then back it off the number
of
turns
shown below:
*
IGNITION TIMING: 2O”BTDC. IN
0.05
-
0.1
1
mrn
(.0020
-
,0043
in)
EX 0.09
-
0.15
mm
(.0035
-
.0059
in)
G300
l/E
turns
G400
2
turns
*
If the clearance is less than the standard
2)
Adjust idle speed
as
outlined left.
~
limit, grind valve stem or replace valve.
-.
CYLINDER HEAD
GASKET
PILOT
SCREW
N VALVE
i
!,
CONTACT
BREAKER ASSY
The CDI type does not require adjustment.
I
i
A
throttle control cable (optional) may be used in
any
one
of
the
four
pull
directions shown.
Use
:I
either a
solid
core wire, or a flexible core wire with
4
a
return
spring and wire end.
j
THROTTLE CONTROL
Wire end
e
Flexible wire
core, mounting
BATTERY
t
Recommended battery
is
*Use only automobile
12V-32AH.
type vinyl covered wire
,fL,,/
effective diameter is
(for
low
voltagej whose
&
(0.172
in) and which
utilizes press fit terminals
between the battery and
the engine. Length must
,/
7
+Protect the terminals
be within lm
(3
Ft).
with grease and com-
pletely cover the positive
cap. When connecting
terminal with
a
rubber
and negative leads are
terminals, ensure posltive
correctly connected.
a
j-
more than
4.4
mrn
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Honda Engines G300 Electric Start at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Honda Engines G300 Electric Start in the language / languages: English as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info