630639
1
Zoom out
Zoom in
Previous page
1/2
Next page
1
HOW TO GET STARTED
HOMELITE ART WORK
Art Part No. : 987000616 Rev. 00
Where Used : 987000616
Refer to Drawings for Dimensions.
987000616
1-20-09 (REV:00)
Make The Most Of Your Purchase!
CALL
1-800-242-4672
www.homelite.com
Material: 60lb. Stock Paper.
Color: Lift-off Bright Pink.
FRONT
For any questions about operating or maintaining your product, call the Homelite Help Line !
Your Product has been fully tested prior to shipment to ensure your complete satisfaction.
Troubleshooting tips are available in your operator's manual.
Go to www.homelite.com and register your new tool on-line.
2
3
4
5
Stand behind the unit with the tines on the ground and the
work area clean and free of obstructions then depress the
switch lock-out.
Carefully remove the product and any accessories from the box. Make sure that all items listed are included.
Loosen the two handlebar knobs. Unfold the handlebar into operating postion. Retighten the handlebar knobs.
To install the tines, lean the unit back on its wheels so that the handlebar rests on the ground.
NOTE: This view of the gearbox for tine installation is from the front of the cultivator.
Place tine C on the tine shaft to the left of the gear box. The stamped side of the tine should face away from the gear box.
Place tine B on the tine shaft to the right of the gear box. The stamped side of the tine should face away from the gear box.
Place a felt washer on each side of the tine shaft, and slide to rest against the inner tines.
Place the outer tine stamped D on the left side of the tine shaft. The stamped side should face in toward tine C.
Place the outer tine stamped A on the right side of the tine shaft. The stamped side should face in toward tine B.
Note: When installed correctly, the angled edge of the tine blades
should face the ground.
To secure the tines to the tine shaft, insert the hitch pin into
the holes located on either side of the tine shaft.
NOTE: The unit will not operate properly if the tines are
installed incorrectly. If you notice a problem with the cultivating
operation of the unit, check for proper tine positioning.
6
7
Route an approved outdoor extension cord through the
upper extension cord retainer ring.
8
9
10
6
Pull the switch trigger toward the handlebar to begin tine rotation.
To stop the cultivator, release the switch trigger.
Position the front handle as shown. Depress the buttons on the handle and insert into the frame.
Press down on the handle until the button on the handle clicks into place.
Locate the axles, hitch pins, washers and wheels. Slide the wheel onto the axle. Place a washer on the outside of the wheel
and slide to rest against the wheel. Push the hitch pin into the hole on the end of the axle to secure the wheel/drag bar assembly.
Repeat with the second wheel.
To install the wheel/drag stake assembly, remove the adjustment knob located at the back of the tine shield. Insert the
wheel/drag stake assembly into the bracket at the back of the tine shield. Insert adjustment knob through holes in bracket,
passing through desired hole in wheel/drag stake assembly, to secure wheel/drag stake assembly at desired height.
Thread the adjustment knob into the nut and tighten, to secure wheel/drag stake assembly.
Tie extension cord to plug connector.
Plug the cultivator into the extension cord.
7
Tine D Tine C
Tine B
Tine A
WARNING: This How To Get Started Procedure is not a substitute for reading the operator’s manual.
To reduce the risk of injury, user must read and understand operator’s manual before using this product.
10
8
9
3
4
2
5
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Homelite UT46510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Homelite UT46510 in the language / languages: English, French as an attachment in your email.

The manual is 3,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Homelite UT46510

Homelite UT46510 User Manual - English, French, Spanish - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info