30196
3
Zoom out
Zoom in
Previous page
1/4
Next page
Set-up and installation of your new Ranger 2N
Please read the following section carefully before
attempting to install the Ranger 2N system
When installing the system in the model of your choice, please follow the
detailed instructions found in the model kit.
1. The transmitter requires eight and the receiver battery pack needs four
AA size batteries. These can be Alkaline or Ni-cad cells. If you choose to
install Ni-cad batteries, the optional CG-25A(110V)or CG-22(220V)
Hitec overnight wall charger can be used to re-charge them.
2. When loading the batteries, make sure the receiver and transmitter switches
are in the "off" position.
3. Open the battery door in the back of the transmitter by squeezing the tab on the
bottom of the battery door and lifting up.
4. Load batteries into the appropriate slots, taking care to install according to the
proper polarity.
5. Replace the battery door and turn the power "on". If the batteries are fresh and
charged, the green L.E.D. will be lit. Should the battery power drop to an unacceptable
level, the red L.E.D. will glow, warning the user of impending failure. At this point,
replace the alkaline cells or charge the batteries if they are Ni-cads.
1. Install the receiver to protect it from vibration and potential crash damage.
2. Typically one servo will be used for the steering and the other servo will be
used to operate a mechanical speed control, or not used at all and an optional
electronic speed control will be used.
3. If your vehicle is electric, there will be a proportional speed control you will wish
to use. If your speed control is mechanical, it will require a servo to operate it.
The battery and switch harness found in the kit must also be used to provide the
receiver with power.
4. Should your model use an electronic speed control that has the option of the
B.E.C. circuit (battery eliminator circuit), this feature will eliminate the receiver
battery and use the motor battery to feed the receiver and servos through the
speed control.
5. Please refer to the instructions that accompany your electronic
speed control for installation.
BATTERY INSTALLATION
RADIO SYSTEM INSTALLATION
4 5
PRESS BOTTOM AND
OPEN UPWARD
BATTERY COVER
8 AA SIZE BATTERY. BE
CAREFUL TO LOAD RIGHT
DIRECTION OF BATTERIES( + - )
(Electronic Speed Control)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitec RANGER_IIN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitec RANGER_IIN in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info