511981
4
Zoom out
Zoom in
Previous page
1/41
Next page
3
English
PRECAUTIONS ON USING DEMOLITION
HAMMER
1. Wear ear protections
Exposure to noise can cause hearing loss.
2. Do not touch the bit during or immediately after
operation. The bit becomes very hot during
operation and could cause serious burns.
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power input* 1140W
Full-load impact Rate 1600/min
Weight (without cord, side handle) 9.5 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
SPECIFICATIONS
3. Before starting to break, chip or drill into a wall,
floor or ceiling, thoroughly confirm that such items
as electric cables or conduits are not buried inside.
4. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
5. Wear a dust mask
Do not inhale the harmful dusts generated in
drilling or chiseling operation. The dust can
endanger the health of yourself and bystanders.
Hammer Grease A
500g (in a can)
Optional accessories are subject to change without
notice.
APPLICATIONS
Breaking concrete, chipping off concrete, grooving, bar
cutting, and driving piles.
Application examples:
Installation of piping and wiring, sanitary facility
installation, machinery installation, water supply and
drainage work, interior jobs, harbor facilities and other
civil engineering work.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a power receptacle while
the power switch is in the ON position, the power
tool will start operating immediately, which could
cause a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Tool Mounting:
NOTE
For tools such as a bull point and a cold chisel,
use only HITACHI genuine parts.
(1) Clean, then smear the tool shank with the grease
provided.
(2) Slide the tool holder in the direction of arrow A
and rotate it 180°.
Turn the notch of the tool shank downward and
insert it fully into the hexagonal hole of the front
cover. (Fig.1)
(3) Turn the tool holder and align the front cover mark
with the tool holder mark to secure.
STANDARD ACCESSORIES
(1) Case ........................................................................... 1
(2) Bull Point ................................................................... 1
(3) Side Handle
I type: Side handle ......................... 1
II type: D type handle ................... 1
Either type I or type II Side handle is attached.
(4) Dust cover ................................................................. 2
(5) Hammer Grease A ................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES
(sold separately)
Crushing
(1) Bull Point
Total Length: 300, 380, 450mm
Asphalt Cutting
(1) Cutter
Width: 50, 75mm
Total length: 400mm
Groove Digging and Edging
(1) Cold Chisel
Total Length: 300, 380, 450mm
01Eng_H55SA_WE 4/20/07, 4:27 PM3
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi H55SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi H55SA in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info