567005

Hitachi FDV16 Manual

6
Zoom out
Zoom in
Previous page
1/30
Next page
English
4
Model FDV16VB FDV16T FDV16
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power Input 550W*
High Low
No-Load Speed 0 – 2900/min 2900/min
2900/min 2300/min
Capacity: Steel 13mm
Concrete 16mm
Wood 25mm
Weight (w/o cord) 1.6kg
STANDARD ACCESSORIES
For entire area
(1) Side handle ............................................................... 1
(2) Depth stopper ........................................................... 1
For partial areas
(1) Chuck wrench ........................................................... 1
(For drill chuck with chuck wrench)
(2) Plastic case................................................................ 1
Standard accessories are subject to change without
notice.
APPLICATION
⅜ By combined action of ROTATION and IMPACT:
Boring holes in concrete, marble, granite, tile, and
similar materials.
⅜ By ROTATION only:
Boring holes in metals, wood and plastics.
Tightening wood screws.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized con-
forms to the power requirements specified on the
product nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Side handle attachment
Attach the side handle to the mounting part.
Rotate the side handle grip in a clockwise direction
to secure it.
Set the side handle to a position that is suited to
the operation and then securely tighten the side
handle grip.
5. Mounting and dismounting of the bit.
For keyless chuck
(1) Mounting the bit
After inserting a driver bit, etc. into the keyless drill
chuck, firmly grasp the ring and tighten the sleeve
by turning it toward the right (in the clockwise
direction as viewed from the front). (See Fig.1)
⅜ If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger
when the sleeve is tightened.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by
turning it toward the left (in the counterclockwise
direction as viewed from the front). (See Fig.1)
NOTE
When the sleeve does not become loose any fur-
ther, fix the side handle to the sleeve. Then, strike
the grip of the side handle to the left in order to
loosen the sleeve,while holding the ring by hand.
(Fig.2)
CAUTION
Do not fix the side handle to the ring of the keyless
chuck because of a risk that doing so may damage
the ring.
For Drill chuck with chuck wrench
Fit the drill bit into the chuck and use the chuck
wrench to secure it, tightening the chuck by each
of the three holes in turn. (Fig.3)
6. Selecting the appropriate drill bit
⅜ When boring concrete or stone:
Use the drill bits for concrete.
⅜ When boring metal or plastic:
Use an ordinary metalworking drill bit.
SPECIFICATIONS
* Be sure to check the nameplate on product as it is subject to change by areas.
Additional rules for impact drills
- Wear ear protection
Exposure to noise can cause hearing loss.
- Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi FDV16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi FDV16 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info