Manual Hitachi D6SH-2 (page 5 of 41) (English, German, Dutch, French, Italian, Portuguese, Spanish)

566268

Zoom out

Zoom in

1/41

English

SPECIFICATIONS

Model D 6SH D 6SB

Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)

Power input 240 W*

No-load speed 4500 min

–1

3000 min

–1

Capacity: steel 6.5 mm 6.5 mm

wood 9 mm 13 mm

Weight (without cord)

Spec. for keyed chuck 0.9 kg

Spec. for keyless chuck 1.0 kg

* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Chuck Wrench (Spec. only for keyed chuck) ...... 1

(2) Stopper Ass’y (Spec. only for keyed chuck).......1

(3) Hook ............................................................................ 1

Standard accessories are subject to change without

notice.

APPLICATION

⅜ Drilling holes into various metals, lumbers and

plastics.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting the drill bit

Fit the drill bit into the chuck and use the chuck

wrench to secure it, tightening the chuck by each

of the three holes in turn. (Fig. 3)

For keyless chuck (Fig. 4)

(1) Mounting the bit

After inserting a drill bit, etc. into the keyless drill

chuck, firmly grasp the ring and tighten the sleeve

by turning it toward the right (in the clockwise

direction as viewed from the front).

⅜ If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger

when the sleeve is tightened.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by

turning it toward the left (in the counter-clockwise

direction as viewed from the front)

5. Selecting the appropriate drill bit

(1) When drilling holes in metals or plastics:

Use ordinary metalworking drill bits;

Applicable drill sizes range from 0.5 mm min. to

6.5 mm max.

(2) When drilling holes in lumber:

Use woodworking drill bits.

For small holes of 6.5 mm dia, or less, use

metalworking drill bits.

PRACTICAL HANDLING PROCEDURES

1. Pressure:

Drilling will NOT be accelerated by placing heavy

pressure on the drill. Such action will only result

in a damaged drill bit, decreased drilling efficiency

and/or shortened service life of the drill.

2. When drilling completely through the material:

When the drill bit bores completely through the

material, careless handling often results in a broken

PRECAUTIONS ON USING DRILL

1. Wear ear protectors with impact drills.

Exposure to noise can cause hearing loss.

2. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

3. When mounting the drill bit, insert it fully into the

drill chuck and completely tighten the drill chuck

with the chuck wrench.

If mounting is not done porperly, it is very dangerous

as the drill bit may slip or loosen during operation.

4. Do not wear gloves made of stuff liable to roll up

such as cotton, wool, cloth or string, etc.

5. Do not touch the bit during or immediately after

operation. The bit becomes very hot during operation

and could cause serious burns.

6. When placing the drill on the floor, make sure that

the drill has stopped completely.

7. Before drilling into a wall, floor or ceiling, thoroughly

confirm that no items such as electric cables or

conduits are buried inside.

8. When working in high position, take care of

downword direction.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi D6SH-2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi D6SH-2 Manual

Product: