616703
4
Zoom out
Zoom in
Previous page
1/108
Next page
4
English
Europe other than Norway, Finland, Sweden,
and Denmark
Disconnect mains plug from electrical outlet
Prohibited action
Warning
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 99.
Standard accessories are subject to change without notice.
APPLICATIONS
Flush cutting and pocket cutting of various materials
Peeling of tiles, caulking, etc.
Polishing wood materials, etc.
SPECIFICATIONS
The speci cations of this machine are listed in the Table on
page 99.
NOTE
Due to HITACHI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Mounting the application tool 1 100
Switch Operation 2 100
Adjusting operating speed
*1
3 100
Sawing 4 101
Sanding 5 101
Selecting accessories*
2
102
The tool is equipped with two modes: “Standard Mode” and
“AUTO Mode”.
(1) Standard Mode
You can change the vibration frequency between 6000
to 20000 min
-1
by adjusting the dial from “1” to “5”.
(2) AUTO Mode
Depending on the workload, AUTO Mode “A” will
automatically change the vibration frequency to 15000
min
-1
or 20000 min
-1
. This has the e ect of lowering
vibration and noise prior to and during operation.
Adjust the dial for the mode and speed that best suits your
task conditions and materials.
*1 Operating speed
Mode Dial Vibration Frequency
Standard Mode 1 – 5 6000 – 20000 min
-1
AUTO Mode A
No load: 15000 min
-1
With load: 20000 min
-1
With AUTO Mode, the vibration frequency may not reach
20000 min
-1
or return to 15000 min
-1
depending on variables
such as the type of work or the attachment in use.
*2 Select accessories that are suited to a speci c task.
For details contact Hitachi Authorized Service Center.
MAINTENANCE AND INSPECTION
1. Inspecting the application tool
Continued use of a dull or damaged application tool
will result in reduced cutting e ciency and may cause
overloading of the motor. Replace the application tool
with a new one as soon as excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this tool
should ONLY be performed by a Hitachi Authorized
Service Center.
5. Replacing supply cord
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer of this agent in order
to avoid a safety hazard.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee Hitachi Power Tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a Hitachi Authorized Service Center.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance
with the following code:
Blue: — Neutral
Brown: — Live
As the colours of the wires in the main lead of this tool may
not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
marked with the letter N or coloured black. The wire
coloured brown must be connected to the terminal marked
with the letter L or coloured red. Neither core must be
connected to the earth terminal.
NOTE:
This requirement is provided according to BRITISH
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except The United Kingdom.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CV350V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CV350V in the language / languages: All languages as an attachment in your email.

The manual is 25,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info