110241
5
Zoom out
Zoom in
Previous page
1/12
Next page
4
MAINTENANCE AND INSPECTION OF SAW BLADE
MOUNT
(1) After use, blow away sawdust, earth, sand, moisture,
etc., with air or brush them away with a brush, etc., to
ensure that the blade mount can function smoothly.
(2) As shown in Fig. 8, carry out lubrication around the
blade holder on a periodic basis by use of cutting fluid,
etc.
Fig. 8
NOTE:
Continued use of the tool without cleaning and
lubricating the area where the saw blade is installed
can result in some slack movement of the lever due
to accumulated sawdust and chips. Under the
circumstances, pull a rubber cap provided on the lever
in the direction of an arrow mark as shown in Fig. 9
and remove the rubber cap from the lever. Then, clean
up the inside of the blade holder with air and the like
and carry out sufficient lubrication. The rubber cap
can be fitted on if it is pressed firmly onto the lever.
At this time, make certain that there exists no
clearance between the blade holder and the rubber
cap, and furthermore ensure that the saw-blade-
installed area can function smoothly.
Fig. 9
CAUTION:
Do not use any saw blade with a worn-out blade hole.
Otherwise, the saw blade can come off, resulting in
personal injury. (Fig. 10)
Fig. 10
7. Adjusting the base
This unit employs a mechanism that can adjust the
base mounting position in three stages without the
use of a wrench or other tools.
Lever
Blade holder
Machine oil
Lever
Rubber cap
Blade
Blade hole
(1) Press a pushbutton. When you do this, a base lever
will jump out to prepare the base for adjustment.
(Fig. 11)
Fig. 11
2) Push up the base tip and jog the base back and forth.
(Fig. 12)
Fig. 12
(3) You can adjust the base position in three stages. Move
the base at an interval of about 15 mm, find the
position where the base hooks, and press in the base
lever with your fingers. The base is secured when you
hear the clicking sound. (Fig. 13)
Fig. 13
8. Adjusting the blade reciprocating speed
This unit has a built-in electronic control circuit that
makes it possible to adjust the variable speed of the
saw blade either both by pulling a switching trigger
or turning a dial. (Fig. 14)
Push button
Base lever
Base
Base lever
01Eng_CR13VBY_Eng.p65 7/19/12, 4:34 PM4
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CR 13 VBY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CR 13 VBY in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi CR 13 VBY

Hitachi CR 13 VBY User Manual - English - 60 pages

Hitachi CR 13 VBY User Manual - English - 60 pages

Hitachi CR 13 VBY User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info