565917

Hitachi CL10SA Manual

4
Zoom out
Zoom in
Previous page
1/60
Next page
English
3
PRECAUTIONS FOR STUD CUTTER
WARNING!
1. Be sure to use the unit with the rated voltage
specified on the nameplate. Use of the unit at a
voltage exceeding the specification on the
nameplate can result in a dangerously high rotation
speed and injury.
2. Make sure that you hold the main unit firmly
during operation. Unless you hold it firmly, you
will be exposed to a risk of injury.
3. If the unit malfunctions during operation or you
hear any abnormal noise, immediately turn off the
switch and stop operation. Contact the store where
you bought the unit or a Authorised Hitachi Servise
Center, and ask for checkup and/or repair. Use of
the unit without checkup and repair can result in
injury.
4. If you accidentally drop the unit or knock it against
something, thoroughly examine the unit and
ensure that there are no damages, cracks, or
deformations on the cutter and unit.
CAUTIONS:
1. Install the cutter and accessories securely according
to the handling instructions. If you fail to install
them properly, they may come off and cause an
injury.
2. Be sure to unplug the power cord from the
receptacle when the cutter is checked, cleaned,
and replaced. Failure to do so can result in a
serious injury.
3. Never bring the cutter near your fingers when
operating the switch.
4. Do not use for cutting screws other than soft steel
studs. This tool is designed especially for cutting
of soft steel studs. Using this tool for brass or
stainless steel screws could cause distortions in
the screw threads, thereby preventing insertion of
nuts.
Never use to cut tempered bolts, screws of differing
sizes, reinforcing rods, etc.
5. Use by changing the special cutters according to
the size of the studs. Cutting with cutters of the
wrong size could damage to the continuous thread
studs or the cutter edges.
6. Make sure that the threads on the studs and those
on the cutter are correctly meshed before starting
to cut. Cutting when the threads are not meshed
could cause damage to the studs and the cutter.
7. If the cutter has been attached in the wrong
direction or the bolt for cutter attachment is loose,
this could cause damage to the cutter edge and
could lead to premature damage to the main unit.
Be very careful to attach the cutter correctly.
8. Cutting studs at short lengths of 10 millimeters
or less will create an insufficient meshing length
between the cutter and studs, thus causing damage
to the cutter. Always cut at lengths of more than
10 millimeters.
9. When cutting studs secured to narrow locations,
be sure that there is at least 8 millimeters between
the stud and the surrounding materials.
If the distance is less than 8 millimeters the cutter
could contact the surrounding materials, thereby
causing damage to the cutter and the main unit.
10. When using this equipment at heights, make
doubly sure prior to use that there is no one
standing in the area immediately below you. Place
the tool in a safe and stable place when not using
at the moment.
SPECIFICATIONS
STANDARD ACCESSORIES
Voltage 230 V
Power Input 190 W
No-load stroke 0–32 min
-1
Capacity: Soft steel studs ⅜ M10 × 1.5 ⅜ M8 × 1.25 ⅜ M6 × 1
(Size of studs for cutting) ⅜ W3/8" × 1.5875
Weight 2.7 kg (excluding cord)
1 Hexagon bar wrench ................................................ 1
2 M8 Cutter ................................................................... 2
3 M8 Trimmer ............................................................... 1
4 Plastic case ................................................................. 1
Standard accessories are subject to change without
notice.
1
2
3
4
01Eng_CL10SA_WE 08/12/15, 11:573
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi CL10SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi CL10SA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info