616686
11
Zoom out
Zoom in
Previous page
1/84
Next page
11
English
7. Adjust the bands and strap in consideration of the job
in hand and ease-of-movement. Also make the most
e cient use of the armband supplied in accordance with
the characteristics of the cordless power tool being used.
NOTE
Use the arm band when using cordless bush trimmers
to prevent the adapter cable from being accidentally
severed. (Fig. 6)
CHARGING
Before using the power tool, charge the back pack power
supply as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red. (At 1-second intervals)
2. lnsert the adaptor of back pack power supply into
the charger.
Place the back pack power supply in a horizontal
position and turn it on by the switch on the side. Firmly
insert the adaptor into the charger until the line is
visible, as shown in Fig. 7.
NOTE:
If the pilot lamp of the charger lights in green (high
temperature standby status) when the adaptor is
inserted into the charger, check that the battery status
lamp on the back pack power supply control panel is lit
in red.
If the battery status lamp is OFF, the back pack power
supply switch may be turned OFF.
If the back pack power supply switch is turned OFF,
disconnect the adaptor and turn on the switch before
reinserting the adaptor.
3. Charging
When inserting an adaptor of back pack power supply
in the charger, the pilot lamp will light up continuously in
red.
When the back pack power supply becomes fully
recharged, the pilot lamp will blink in red. (At 1-second
intervals.) (See Table 1)
(1) Lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
back pack power supply.
Table 1
Indications of the pilot lamp
The
pilot lamp
lights or
blinks in
red.
Before
charging
Blinks Lights for 0.5 seconds. Does not light for 0.5
seconds. (o for 0.5 seconds)
While
charging
Lights Lights continuously
Charging
complete
Blinks Lights for 0.5 seconds. Does not light for 0.5
seconds. (o for 0.5 seconds)
Charging
impossible
Flickers Lights for 0.1 seconds. Does not light for 0.1
seconds. (o for 0.1 seconds)
Malfunction in the back pack
power supply or the charger
The
pilot lamp
lights in
green.
Overheat
standby
Lights Lights continuously
Back pack power supply
overheated.
Unable to charge.
(Charging will commence when
back pack power supply cools)
NOTE: The cooling fan does not rotate while the back pack power supply is charging.
(2) Regarding the temperature of the back pack power
supply.
The temperature for back pack power supply are as
shown in the Table 2, and back pack power supply that
have become hot should be cooled for a while before
being recharged.
Table 2
Back Pack Power Supply
Temperature which the
back pack power supply
can be recharged
BL36200 0°C – 50°C
(3) Regarding recharging time
Table 3 shows the recharging time required according
to the type of back pack power supply.
Table 3 Charging time (At 20°C)
Charger
Back Pack Power Supply
UC36YRSL
BL36200 Approx. 10 hours
NOTE
The recharging time may vary according to the ambient
temperature.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger rmly and pull out the adaptor of
back pack power supply.
NOTE
Be sure to pull out the adaptor of back pack power
supply from the charger after use, and then keep it.
When the back pack power supply is not in use, switch
it OFF.
How to make the back pack power supply perform longer.
(1) Recharge the back pack power supply before they
become completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its back pack
power supply.
If you continue to use the tool and exhaust the electric
current, the back pack power supply may be damaged
and its life will become shorter.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi BL36200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi BL36200 in the language / languages: All languages as an attachment in your email.

The manual is 2,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info