Manual Hitachi AW18DBL (page 3 of 300) (All languages)

616685

Zoom out

Zoom in

1/300

English

CAUTION

1. Purge all of the pressure within the washer before

disconnecting the high-pressure hose.

2. Attach all supplied accessories correctly in

accordance with the instruction manual.

Failure to observe this may result in the accessories

becoming detached or in injury.

3. Check to make sure that no foreign matter is

adhering to the object being washed.

Failure to observe this may result in the matter ﬂ ying oﬀ

and causing unexpected injury.

4. Do not spray a jet of water at the areas surrounding

labels on the object being washed.

Failure to observe this may result in the labels peeling

oﬀ .

5. Grip the handle ﬁ rmly when carrying the washer.

6. Children should be supervised to ensure that they

don't play with the appliance.

ADDITIONAL SAFETY WARNINGS

WARNING

1. Do not switch the washer on while the trigger is

being pulled.

Failure to observe this may result in high-pressure water

being sprayed immediately, leading to unexpected

accidents.

2. Do not point the nozzle at people or animals.

Failure to observe this may result in injury.

3. Make sure all residual water is drained from the

washer, the trigger gun and the hose, etc., after use.

Failure to observe this may result in freezing, leading to

malfunctions.

4. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

5. Never disassemble the rechargeable battery and

charger.

6. Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

7. Do not dispose of the battery in ﬁ re. If the battery is burnt,

it may explode.

8. Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

9. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or inﬂ ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

CAUTION

1. Keep the work area neat and tidy

Dirty water will be sprayed about when using the washer.

It is therefore necessary to check the area to make sure

there are no hindrances, and keep the work area neat

and tidy.

2. Situating the washer

Select ﬂ at locations where the washer will not be

splashed with water when cleaning.

3. Set the switch to “OFF” immediately if the hose becomes

detached from the faucet or washer, and if water is no

longer being fed to the washer.

Failure to observe this may result in immediate

malfunctions (dry operations.)

4. Set the switch to “OFF” without fail when temporarily

suspending operations.

Failure to observe this may result in the motor

automatically starting up.

5. Place your ﬁ nger in the center of the trigger during

operations.

Failure to observe this may result in injury from pinched

ﬁ ngers.

Grip the gun and nozzle ﬁ rmly with both hands.

6. This product contains a strong permanent magnet in the

motor.

Observe the following precautions regarding adhering of

chips to the tool and the eﬀ ect of the permanent magnet

on electronic devices.

○ If you use a pacemaker or other electronic medical

device, do not operate or approach the tool. Operation

of the electronic device may be aﬀ ected.

○ Do not use the tool in the vicinity of precision devices

such as cell phones, magnetic cards or electronic

memory media. Doing so may lead to misoperation,

malfunction or loss of data.

NOTE

1. Loose connections may result in water leaks.

2. Moisten the O-ring with water to facilitate the connection

if it is diﬃ cult to insert the hose and nozzle.

3. Remove all dirt, mud and other matter from the trigger

gun’s entry hole and the protrusion on the nozzle.

4. Set the spray adjustment to “Jet” ﬁ rst of all, and then

gradually move it to the “Spray” position while pulling the

trigger.

Note that there is a chance of the water being sprayed

horizontally over a wide area if this is rotated fully to the

“Spray” position.

5. Note that the nozzle may be damaged if it is forced to

move past the stop position when alternating between

“Jet” and “Spray”.

6. Commence initial washing approximately 1 meter away

from the targeted item, and then move gradually closer

while checking the level of cleaning until you reach a

distance in which soiling is eﬀ ectively washed away.

The pressure of the spray from the washer is

approximately 7-times greater than tap water. High-

pressure water jets may therefore damage or peel the

coating from the items being washed.

7. There are cases when the water spray will appear

unstable owing to the fact that air that has built up in

the pump and hose is purged together with the water

immediately after use. In this event, allow the water to

ﬂ ow out until it stabilizes.

8. Leave two or more seconds gap between pulling and

releasing the trigger.

Failure to observe this may result in the pressure switch

malfunctions.

9. Do not turn the switch ON when the tank is empty or the

faucet is shut oﬀ .

Failure to observe this may result in malfunctions.

10. The motor will automatically switch oﬀ once suﬃ cient

water pressure has built up inside the washer.

11. Lock the trigger with the trigger stopper during pauses

and after washing has been completed.

12. Leaving the washer switched on may result in dry

operations, leading to malfunctions.

13. The use of the battery in a cold condition (below 0 degree

Centigrade) can sometimes result reduced amount of

work. This, however, is a temporary phenomenon, and

returns to normal when the battery warms up.

14. Water may leak if the tank containing water is attached

and the high-pressure hose is not.

○ Attach the high-pressure hose and trigger gun before

attaching the tank.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi AW18DBL in the language / languages: All languages as an attachment in your email.

The manual is 21,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi AW18DBL Manual

Product: